Campbell Hausfeld WG3080 Instrucciones De Funcionamiento Y Manual De Piezas página 8

Tabla de contenido

Publicidad

Idiomas disponibles

Idiomas disponibles

Wire Feed Arc Welder
Welding Guidelines
General
This welding machine can utilize the Flux
Cored Arc Welding (FCAW) process or
the Gas Metal Arc Welding (GMAW)
process. The weld must be protected
(shielded) from contaminants in the air
while it is molten. The FCAW process
uses a tubular wire with a flux material
inside. The flux creates a shielding gas
when melted. The GMAW process uses
inert gas to shield the weld while
molten.
When current is produced by a
transformer (welding machine) and
flows through the circuit to the weld
wire, an arc is formed between the end
of the weld wire and the work piece.
This arc melts the wire and the work
piece. The melted metal of the weld wire
flows into the molten crater and forms a
bond with the work piece as shown
(Figure 7).
Nozzle
Shielding
Gas
Slag
Weld
Crater
Work Piece
Figure 7 - Weld Components
Arc Welding Basics
Six basic techniques affect weld quality.
These are: wire selection, heat setting,
weld angle, wire speed, travel speed, and
electrode extension. An understanding of
these techniques is necessary for effective
welds.
HEAT SETTING
The correct heat involves the adjustment
of the welding machine to the required
setting. Heat or voltage is regulated by a
switch on the welder. The heat setting
used depends on the size (diameter) and
type of wire, position of the weld, and
the thickness of the work piece. Consult
specifications listed on the welder. It is
suggested that the welder practice with
scrap metal to adjust settings, and
compare welds with Figure 9.
www.chpower.com
WIRE TYPE AND SIZE
The correct choice of wire type involves
a variety of factors, such as welding
position, work piece material type,
thickness, and condition of surface to
be welded. The American Welding
Society, AWS, has set up certain
requirements for each type of wire.
FLUX-CORED WIRE
E - 7 0 T - GS
AWS E71T-GS or E71T-11 is
recommended for this welder.
Contact
SOLID WIRE
Tip
ER - 70 S - 6
Flux
(Gasless
only)
Wire
ER-70S6 is recommended for this
welder.
WELD ANGLE
Weld angle is the angle at which the
nozzle is held during the welding
process. Using the correct angle ensures
proper penetration and bead formation.
As different welding positions and weld
joints become necessary, nozzle angle
becomes an increasingly important
factor in obtaining a satisfactory weld.
Weld angle involves two positions -
travel angle and work angle.
Travel angle is the angle in the line of
welding and may vary from 5º to 45º
from the vertical, depending on welding
conditions.
Work angle is the angle from
horizontal, measured at right angles to
the line of welding. For most
applications, a 45º travel angle and 45º
work angle is sufficient. For specific
applications, consult an arc welding
handbook.
Weld strength, times
10,000 pounds per
square inch
Welding positions (0 for
flat or horizontal, 1 for
any position)
Tubular flux-cored wire
Flux type
Weld strength, times
1,000 PSI
Solid wire
Wire composition
8
5º - 45º
WORK ANGLE
5º - 45º
TRAVEL ANGLE
Figure 8 - Weld Angle
WIRE SPEED
The wire speed is controlled by the
knob on the front panel. The speed
needs to be "tuned" to the rate at
which the wire is being melted in the
arc. Tuning is one of the most critical
functions of wire feed welding. Tuning
should be performed on a scrap piece
of metal the same type and thickness as
that to be welded. Begin welding with
one hand "dragging" the torch nozzle
across the scrap piece while adjusting
the wire speed with the other hand.
Too slow of speed will cause sputtering
and the wire will burn up into the
contact tip. Too fast a speed will also
cause a sputtering sound and the wire
will push into the plate before melting.
A smooth buzzing sound indicates the
wire speed is properly tuned. Repeat
the tuning procedure each time there is
a change in heat setting, wire diameter
or type, or work piece material type or
thickness. For Aluminum, wire speed is
typically set higher (7-9 speed range).
TRAVEL SPEED
The travel speed is the rate at which the
torch is moved across the weld area.
Factors such as diameter and type of
weld wire, amperage, position, and work
piece material thickness all affect the
speed of travel necessary for completing
a good weld (See Figure 9). When the
speed is too fast, the bead is narrow and
bead ripples are pointed as shown. When
the speed is too slow, the weld metal
piles up and the bead is high and wide.
For Aluminum, travel speed is typically
faster.

Publicidad

Tabla de contenido
loading

Este manual también es adecuado para:

Wg3090Wg4130

Tabla de contenido