Menu Sequence Overview - Bühler technologies Nivotemp NT MD Guía Rápida

Nivotemp NT MD

8 Menu Sequence Overview

Main menu Submenu 1
Configuration t___
Shortcut
or 60s no action:
Equipment configuration
Exit main/submenu
____
Display
____
Measurement display
Temperature ____ Out 1
tEMP
Temperature main menu Settings menu OUT1
Out x
Settings menu OUTx
Analog Out1
Settings menu Analog 1
Exit
Exit menu level
b. E F
Basic EF Reset
Factory setting
Basic Adv. Functions
Set error handling
Error handling
Set Unit Temp
Temperature unit
reassign O1
Assignment Out 1
reassign O2
Set Out 2
Display Rate
Display rate
Lock Device
Keylock
Exit
Exit menu level
Diagnostic diA Journal Out
Diagnostics menu Logs output
Max/Min Temp
Max/Min memory
Set Journal Out
Output monitoring
Delay MM
Min/Max Delay
Exit
Exit menu level
Exit E
Exit menu level
BX100022 ◦ 11/2020
Submenu 2 Submenu 3
+
out1 ____ ____
SP1
FH1 F1. H i ____
Switching point 1
____
rP1
FL1 F1. L o ____
Switch-back point 1
____
EF 1 EF1 Delay SP 1
Advanced Functions
Delay OUT1 On
Delay RP 1
Delay OUT1 Off
Set Out 1
Definition OUT1
Check Out 1
Functional test OUT1
LED Out 1
Function status LED1
Exit
Exit menu level
____
Exit E
Exit menu level
____
out_ See menu structure Out1
Not applicable for version with
analogue output
____ ____
An1 Analog Max1 A1. H i
Set maximum value
____
Analog Min1 A1. L o
Set minimum value
____
Set A.Out1 A. o u1
Output function
____
Check An1 C. A n1
Functional test Analog 1
E ____
Exit
Exit menu level
E
rES
Errh
t. u ni
r. o u 1
r. o u 2
di5
Loc
E
J. o ut
t. M M
SJ. o u
dt. M M
E
Settings and Display Menu
____
Switch
____
Switches the measurement display level/temperature
Switch view
Selection menu ____
____ SP1 Setting the switching point /
FI. H i Sets a value for frequency 100 Hz (only OUT1 and OUT2)
0°C - 100°C
____
Selection menu Set switch-back point /
____ rP1
FI. L o Sets a value for frequency 1 Hz (only OUT1 and OUT2)
0°C - 100°C
____ Selection menu ____
dS1
___
Amount of time the signal must be present for output OUT1 to trigger.
0 - 100 Setting range: 0...100 seconds (for frequency output without function)
____ ____
dr1 Selection menu
___
Amount of time the signal must be present for output OUT1 to switch back.
0 - 100 Setting range: 0...100 seconds (for frequency output without function)
Definition of switching characteristics for output 1:
____ ____
ou1 Selection menu
___
Hno Hnc Hysteresis function NO contact or NC contact
Hno - FM
Fno Fnc Window function NO contact or NC contact /
n. o P Normal switching output operation
____ Selection menu ____
C. o u1
____
oFF Switching output Off /
n. o p - on
on Switching output On /
____ Selection menu ____
LEd1
L=__ LED = output: follows switching output
L= o
L= o - L=-o L=-o LED = -output: inverted to switching output
____
E
Selection menu ____
____
Sets the maximum analogue output signal to a defined value.
(Note: Max. – Min >= 10 % of the measuring range)
0°C - 100°C
____
Selection menu
____
Sets the maximum analogue output signal to a defined value.
0°C - 100°C (Note: Max. – Min >= 10 % of the measuring range)
____
Selection menu
_ _ Selecting the analogue output function:
i 1 - u 3 i I 4...20 mA
____
Selection menu Analogue output normal mode /
____ n. o P
HALF Output mean analogue value /
n. o P - Lo
Alternate menu for version with analogue output
Not applicable when ordered with 2 or more switching outputs
____
Confirm ___
Resets the device to factory settings
no - YES
Selection menu ___
Selection menu ____
Disable/enable normal error handling and analysis
´no - YeS
Selection menu °_ Selecting the temperature unit displayed:
°C [Celsius],
°C - °F
____
Selection menu ____
Assigns switching outputs to function or to error signal
Err - oil - tEMP
____
Selection menu
____
Assigns switching outputs to function or to error signal
Err - oil - tEMP
____
Selection menu
____ Selecting the display refresh rate:
FASt - off FASt [fast], Medi [medium], SLo [slow],
____
Selection menu ___
Activating the keylock by entering a numerical code > 0 Master code 287
0 - 999
____
Selection menu ____
Displays the last 6 alarms + delete function.
Jor I - --- Display: JorX
____
Selection menu ____ Displays the limits + delete function.
Display: Value – amount of time passed in hours/days; scroll through journal with ▲▼
____ - ---
____
Selection menu
out_
Selecting the alarm output to be logged
Out1 - Out_
____
Selection menu
___
Amount of time the signal must be present before saving the maximum /
minimum value. Setting range: 0...100 seconds
0 - 100
FH1 Define maximum window limit
FL1 Define minimum window limit
Frequency output 1-100 Hz
FM
F1 Simulation 1 Hz
F100 Simulation 100 Hz
u 3 0...5 V
u 1 2...10 V u 2 0...10 V
Hi Output maximum analogue value
Lo Minimum analogue value output
°F [Fahrenheit]
oFF [Display off]
X – amount of time passed in hours/days; scroll through journal with ▲▼
Bühler Technologies GmbH 13