Before Using A New Chain Saw - Husqvarna 414 EL Manual De Instrucciones

lectrical safety
It is recommended that you use a Gorund Fault Circuit
Interrupter (GFCI) with a tripping current of not more than
30mA. Even with a GFCI installed 100% safety cannot be
guaranteed and safe working practice must be followed at
all times. Check your GFCI every time you use it.
Before use, examine the cable for signs of damage or
ageing. If the cable is found to be defective, take the
product to an Authorized Service Center and have the
cable replaced.
Do not use the product if the electric cables are damaged
or worn.
Immediately disconnect from the mains electricity supply if
the cable is cut, or the insulation is damaged. Do not touch
the electric cable until the electrical supply has been
disconnected. Do not repair a cut or damaged cable. Take
the product to an Authorised Service Centre and have the
cable replaced with a genuine spare cable.
Always make sure that the cable/extension cord is kept
behind the user, ensuring that it does not create a source
of danger for the user or for other persons, and check that
it cannot be damaged (by heat, sharp objects, sharp
edges, oil, etc);
Position the cable so that it will not be caught on branches
and the like, during cutting.
Always switch off at the mains before disconnecting any
plug, cable connector or extension cable.
Switch off, remove plug from the mains and examine
electric cable for damage or ageing before winding cable
for storage. Do not repair a damaged cable. Take the
product to an Authorised Service Centre and have the
cable replaced.
Remove the plug from the mains before leaving the product
unattended for any period.
Always wind cable carefully, avoiding kinking.
Use only on AC mains voltage shown on the product rating
label.
The chainsaw is double insulated to EN60745-1 & 2-13.
Make sure your extension cord is in good condition.
Inspect extension cord before use and replace if damaged.
Do not use a damaged cord. Cord insulation must be intact
with no cracks or deterioration. Plug connectors must be
undamaged. Damaged extension cords increase the risk of
electric shock.
Ground Fault Circuit Interrupter (GFCI) protection
should be provided on circuit or outlet to be used.
Receptacles are available having built-in GFCI protection
and may be used for this measure of safety. Inspect chain
saw cords periodically and if damaged, have repaired by an
authorized service dealer.
12 – English
GENERAL SAFETY PRECAUTIONS
WARNING! To reduce the risk of electrical
!
shock, this equipment has a polarized plug
(one blade is wider than the other) and will
require the use of a polarized extension cord.
The appliance plug will fit into a polarized
extension cord only one way. If the plug does
not fit fully into the extension cord, reverse
the plug. If the plug still does not fit, obtain a
correct polarized extension cord. A polarized
extension cord will require the use of a
polarized wall outlet. This plug will fit into the
polarized wall outlet only one way. If plug
does not fit fully into the wall outlet, reverse
the plug. If the plug still does not fit, contact
a qualified electrician to install the proper
wall outlet. Do not change the equipment
plug, extension cord receptacle, or extension
cord plug in any way.
Cables
• Extension cables are available from your local Approved
Service Centre.
• Only use approved extension cables.
• If you want to use an extension cable when operating your
product, only the following cable dimensions should be
used: - #14 AWG : max length 7.6 m (25 ft) - #12 AWG :
max length 15 m (50 ft) - #10 AWG : max length 30 m (100
ft) An undersized extension cord will cause a drop in line
voltage resulting in loss of power and overheating. If in
doubt, use the next heavier gauge. The lower the gauge
number, the heavier the cord. Do not use multiple cords.

Before using a new chain saw

• Please read this manual carefully.
• Fill with chain oil. See instructions under the heading Filling
with chain oil.
• Do not use the chain saw until sufficient chain oil has
reached the chain. See instructions under the heading
Lubricating cutting equipment.
• Check that the cutting equipment is correctly fitted and
adjusted. See instructions under the heading Assembly.
• Long-term exposure to noise can result in permanent
hearing impairment. So always use approved hearing
protection.
• This saw is intended for use between the temperatures of -
20°C (-4°F) and +40°C (104°F).