Tabla de contenido
Publicidad
Idiomas disponibles
Idiomas disponibles
This system is a backup to your primary sump pump. It is designed to provide flood prevention during power outages or primary pump failure. This system is unique in that it
has self-testing and communication features (if using with Gateway and Z Control
Construction
Performance
Continuous Running Time
Duty Cycle of 10%
Connection
Construction
Power Requirement
Consumption
Output
Charger output
Connections
Construction
Connections
Construction
Safety
* When AC power is available, DC Pump operation does not deplete battery.
OPERATIONAL
FLOAT SWITCH
HIGH WATER
FLOAT SWITCH
CLAMP
DC PUMP
1.5" PVC TEE SCH 40
1.5" INLINE CHECK VALVE
PERFORMANCE
The DC pump performance with fully charged 12 V battery
Discharge
5
Feet of Head
(1.5 m)
Flow
39
GPM (LPM)
(148)
The DC controller is equipped with a 14 amp charger for maintaining the battery
in a ready state and recharging the battery after use when AC power is restored.
Time for recharge depends upon the amount of power consumed by the pumping
cycle during the AC power interruption. The pump may go back to the ready run
position in a very short period of time. A completely drained battery may require up
to 24 hours for full recharge. If battery does not charge properly, the LED will flash
red. The controller is able to supply the pump with power to run the pump on AC
when available without drawing power from the battery.
Non-corrodible plastic, premium seals
30 GPM at 10' (113 LPM at 3 m)
5 hours
2 days
6' (1.8 m) wire with insulated terminals
18g steel with polyester membrane overlay
115 V 15 amp circuit
Up to 3 amps at 115 V
Full power to DC Pump*
14 amp multi-stage
10' (3 m) AC power cord, 6' (1.8 m) DC charging cable, connections for pump, low level switch, operation switch, high water switch, Z Control
Plastic housing with polyester membrane overlay
WiFi, Ethernet, DC Power Adapter, RJ45 Z Control
Non-corrodible plastic
Snap tight lid, keeps battery safe and clean
CLAMP
10
15
20
(3 m)
(4.6 m)
(6 m)
30
20
6
(114)
(76)
(23)
© Copyright 2016 Zoeller
DESCRIPTION
Cloud).
®
Device Ports, USB (not for public use)
®
CLAMP
(OPTIONAL)
FLOAT CLIP
LOW WATER CUTOFF
FLOAT SWITCH
(OPTIONAL)
ETHERNET CABLE
Z CONTROL
GATEWAY
AQUANOT ACTIVE
®
CONTROLLER
30 AMP FUSE
12 VOLT
DEEP CYCLE BATTERY
BATTERY BOX
SK3047
The DC emergency pump system requires a good quality, 12 volt battery to obtain
maximum pumping time during a power outage. A deep-cycle, 12 volt, 105 amp-
22
hour marine battery or larger is recommended and will provide approximately 5
(6.7 m)
hours of continuous pumping time in a sump pump installation with 8' (2.4 m)of
Shut-off
head pressure. In most installations, the pump runs intermittently and the battery
Head
life is extended accordingly. Batteries with top terminals are recommended for
ease of installation. "Wet" cell batteries contain acid, and proper precaution must
be taken when handling. Battery box will accommodate a maximum battery size
of 13½" (34.3 cm) Length x 7" (17.8 cm) Width x 9½" (49.5 cm) Height. AGM
batteries also recommended. Do not use gel batteries or automotive batteries.
Co. All rights reserved.
®
3
Model 508 Active
Item
Description
Pump 12 V DC / Backup
1
(service Part)
®
2
High water float
3
Operational float
4
Low water float (optional)
5
Fuse, 250 V / Agc-30
Clamp, #28 Worm-SS (float
6
switch)
Valve, check / 1.5 Inline /
7
vertical
8
Active controller
Battery box asm (box and
9
cover)
Hardware pak, charger/
10
switch mode
Fitting, asm & clamp "508"
11
(service part)
12
Flapper asm, (service part)
BATTERY SELECTION
®
508-A
Qty
01/14
thru Current
1
153876
1
153479
1
154198
1
153480
1
012353
3
012724
1
30-0238
1
153477
1
10-0764
1
152864
1
152969
1
152970
Publicidad
Tabla de contenido
