Parts List - KNOVA KN 7060 Manual De Instrucciones

TrOuBLEShOOTING
SYMPTOM
Wheel dulls quickly, 1. Feed rate is too aggressive.
grit falls off.
2. Wheel is soft.
3. Wheel diameter too small.
4. Bad wheel dressing.
5. Defective wheel bonding.
Wheel clogs
1. Wheel is too hard.
and workpiece
2. Feed rate is too slow.
shows burn marks.
3. Bad wheel dressing.
4. Coolant required.

PArTS LIST

mod: KN 7060
KEY# D E S C R I P T I O N
1 SCREW (PH) (BLACK)
2 LEFT WHEEL COVER
3 HEX NUT(ZINC COATING)
4 OUTER WHEEL CLAMP
5 WHITE WHEEL (150 X 20 X 32MM)
6 SCREW & WASHER ASSY. ZINC COATING
7 LEFT WHEEL GUARD ASSY.
8 SPARK DEFELECTOR
9 SCREW & WASHER ASSY. (BLACK)
10 LEFT WORK REST SUPPORT
11 BIG FLAT WASHER (BLACK)
12 TOOTHED LOCK WASHER (BLACK)
13 LOCK NUT
14 LEFT WORK REST
15 FLAT WASHER (BLACK)
16 TOOL REST FIXING KNOB
17 LEFT EYESHIELD MOUNT ROD
18 STANDARD SPRING WASHER (BLACK)
19 HEX BOLT (BLACK)
20 MAGNIFY EYESHIELD ASSY.
21 EYESHIELD LOCK KNOB
22 SCREW (PH)
23 FLAT WASHER
24 END CAP
25 INNER WHEEL CLAMP
26 SCREW & WASHER ASSY. (PH)(ZINC COATING)
27 TOOTHED LOCK WASHER (BLACK)
28 WIRE BUSHING
29 CORD CLIP 6P4
30 SCREW & WASHER ASSY. (PH) (ZINC COATING)
31 BASE
32 WAVE WASHER (BLACK)
33 BEARING 6202RZ
34 STATOR
35 ROTOR
36 HEX FLANGE NUT
37 CORD & PLUG
38 SWITCH PLATE
39 RIGHT EYESHIELD MOUNT ROD
40 EYESHIELD ASSY.
41 RIGHT WHEEL GUARD ASSY.
42 WHEEL (150 X 20 X 32MM)
43 HEX NUT (ZINC COATING)
44 RIGHT WHEEL COVER
45 RIGHT WORK REST
46 RIGHT WORK REST SUPPORT
47 COOLANT TRAY
48 HEX FLANGE NUT (BLACK)
49 CARRIAGE BOLT BLACK
50 SCREW (PH) BLACK
51 SCREW & WASHER ASSY. (PH) (ZINC COATING)
52 CAPACITOR 4uF/450V
53 SWITCH
54 COOLANT TRAY CLIP
55 BASE COVER
56 RUBBER FOOT
PROBABLE CAUSE
SPEC.
M5 x 48
M12 LEFT
120#
M5 x 10
M5 x 10
5
5
M5
6
M6 x17
6
M6 x 30
M5 x 14
M4 x 118
4
M4 x 8
4
M4 x 12
D35
M4
60#
M12
M5
M5 x 51
M4 x 8
M6 x 18
1.Decrease feed rate of workpiece into grinding wheel.
2. Select a grinding wheel with a harder bond of material.
3. Replace wheel.
4. Dress the wheel.
5. DO NOT USE – return wheel to point of purchase.
1. Select a grinding wheel with a softer bond of material.
2. Increase the feed rate of the workpiece into the grinding wheel.
3. Dress the wheel.
4. Introduce coolant.
KEY#
QTY
1 SCREW (PH) (BLACK)
4
2 LEFT WHEEL COVER
1
3 HEX NUT(ZINC COATING)
1
4 OUTER WHEEL CLAMP
2
5 WHITE WHEEL (200 X 25 X 32MM)
1
6 SCREW & WASHER ASSY. (PH) ZINC COATING
6
7 LEFT WHEEL GUARD ASSY.
1
8 SPARK DEFELECTOR
2
9 SCREW & WASHER ASSY. (PH) (BLACK)
4
10 LEFT WORK REST SUPPORT
1
11 BIG FLAT WASHER (BLACK)
2
12 TOOTHED LOCK WASHER (BLACK)
2
13 LOCK NUT
2
14 LEFT WORK REST
1
15 FLAT WASHER (BLACK)
4
16 TOOL REST FIXING KNOB
2
17 LEFT EYESHIELD MOUNT ROD
1
18 STANDARD SPRING WASHER (BLACK)
2
19 HEX BOLT (BLACK)
2
20 MAGNIFY EYESHIELD ASSY.
1
21 EYESHIELD LOCK KNOB
2
22 SCREW (PH)
4
23 FLAT WASHER
4
24 END CAP
2
25 INNER WHEEL CLAMP
2
26 SCREW & WASHER ASSY. (PH) ZINC COATING
3
27 TOOTHED LOCK WASHER (BLACK)
2
28 WIRE BUSHING
1
29 CORD CLIP 6P4
1
30 BASE
4
31 SWITCH PLATE
1
32 WAVE WASHER (BLACK)
1
33 BEARING
2
34 STATOR
1
35 ROTOR
1
36 HEX FLANGE NUT
4
37 CORD & PLUG
1
38 SCREW (PH) BLACK
1
39 RIGHT EYESHIELD MOUNT ROD
1
40 EYESHIELD ASSY.
1
41 RIGHT WHEEL GUARD ASSY.
1
42 WHEEL (200 X 25 X 32MM)
1
43 HEX NUT (ZINC COATING)
1
44 RIGHT WHEEL COVER
1
45 RIGHT WORK REST
1
46 RIGHT WORK REST SUPPORT
1 47 COOLANT TRAY
1 48 HEX FLANGE NUT (BLACK)
4 49 CARRIAGE BOLT BLACK
50 STANDARD SPRING WASHER (ZINC COATING)
2
51 HEX BOLT(ZINC COATING)
4
52 CAPACITOR 10uF/450V
2
53 SWITCH
1
54 COOLANT TRAY CLIP
1
55 BASE COVER
1
56 RUBBER FOOT
1
6
57 SCREW & WASHER ASSY. (PH) (ZINC COATING)
4
CORRECTIVE ACTION
mod: KN 7070
D E S C R I P T I O N
6203RZ
SPEC. QTY
M5 x 48 4
1
M16 LEFT 1
2
120# 1
M5 x 10 6
1
2
M5 x 10 4
1
5 2
5 2
M5 2
1
6 4
M6 x 17 2
1
_6 2
M6 x 30 2
1
M5 x 14 2
M5 x 155 4
5 4
2
2
M4 x 8 3
4 2
1
1
1
1
D40 1
2
1
1
M5 4
1
M4 x 8 4
1
1
1
60# 1
M16 1
1
1
1
1
M5 4
M5 x 51 2
D8 2
M8 x 20 2
1
1
1
1
4
M5 x 16 4