Publicidad
Idiomas disponibles
Idiomas disponibles
PART 2 – PROGRAMMING PROCEDURES
A. PROGRAMMING YOUR PIN
Step 1: Choose a 3-digit PIN using any combination of numbers
from 0 to 9.
Step 2: Replace the existing PIN (factory set at 123 for Door 1 and
456 for Door 2) with your chosen PIN as follows:
a. Press numbers 1, 2, and 3 (for Door Two, press 4, 5, 6)
b. Press the
key.
c. Press your new 3-digit PIN.
d. Press the
key again.
Wait 30 seconds before proceeding to B.
(NOTE: To change PINs in the future, see Part 3 – Information.
It will not be necessary to repeat B. PROGRAMMING YOUR
SECURITY CODE.)
B. PROGRAMMING YOUR SECURITY CODE
Step 1: Enter your PIN into the keypad.
Step 2: Press the # key.
Step 3: Press one of the following number keys, depending on your
system brand as checked in Table 1:
• 1 (Linear, Moore-O-Matic)
• 2 (Stanley)
• 3 (Multi-Code)
• 4 (Chamberlain, Lift-Master, Master Mechanic, Sears,
Wayne Dalton)
• 5 (9 code switch Genie)
• 6 (12 code switch Genie)
Step 4: Press the # key again.
Step 5: Enter your code switch numbers from Table 2 or 3, column
by column, beginning with the first column in the table. See
examples below.
Example 1: (Table 2) 9 code switches or random 9 digit code
+
0
3
3
3
–
Press 3 three times, 1 twice, 2 four times.
Example 2: (Table 3) Press 1, 2, 1, 2, etc.
ON
1
1
OFF
2
2
Step 6: Press the # key again.
• If your system has code switches, programming is complete.
Wait 30 seconds and proceed to C. TESTING YOUR SYSTEM to
make sure the K3 activates your opener.
• If your system does not have code switches, you must program
your receiver to accept the random 9 digit code you entered from
Table 2. Wait 30 seconds and proceed to Step 7.
Step 7: (For receivers without code switches)
a. Locate the "smart" programming
button on your receiver panel.
b. Enter your PIN into the keypad.
c. Press and HOLD any additional
number key.
d. Press (for not longer than two
seconds) and release the "smart"
button on the receiver. The adjacent
indicator light will blink.
e. Release the number key.
114A2355B
1
1
2
2
2
1
1
1
1
2
2
2
1
2
9
7
"Smart" (learn)
Indicator Light
Button
©2000, The Chamberlain Group, Inc.
Programming is complete. Wait 30 seconds and proceed to
C. TESTING YOUR SYSTEM to make sure the K3 activates your
opener.
NOTE: To program a second door, return to A and choose a
different PIN. In Step 2a, press 4, 5, 6 instead of 1, 2, 3.
C. TESTING YOUR SYSTEM
Take the unit to the approximate location where it will be mounted.
Stand clear of the garage door, and:
• Enter your PIN.
• Enter any additional number.
If the system has been programmed correctly, the door should open.
If it does not, see D. TROUBLESHOOTING.
NOTE: When using the keypad to open your door, always enter
your PIN and one additional number.
D. TROUBLESHOOTING
• If the door does not open:
– PIN may be incorrect
– Security code may not match operator
– Check battery
• If the keypad does not light up when a number is pressed,
replace battery.
MOUNTING THE K3
Select a smooth vertical surface in a location out of the path of the
moving garage door, but within sight of it. You will need a clearance
of at least 4-1/2 inches above the keypad for the cover.
Remove the slide up keypad cover and the battery cover. Remove
the battery from its compartment (it is not necessary to disconnect
it). Mount the keypad using the screws supplied, then replace
components.
BATTERY REPLACEMENT
The keypad should light up and remain illuminated for approximately
6 seconds after a number is pressed. Replace the 9 volt battery
2
when the keypad lamps become dim. Slide the keypad cover up into
the stop position. Unscrew the battery cover and replace battery.
Memory is not lost when the battery is removed.
INFORMATION
• Entering an incorrect PIN will lock out the unit for 30 seconds.
• To change your PIN:
2
a. Press your existing PIN.
b. Press the
c. Press your new 3 digit PIN.
d. Press the
When changing PINs in the future, it is not necessary to re-
program your security code.
CAUTION
Use of this wireless keypad should be limited to responsible
adults. Automatic Gate and Garage Door systems are
dangerous. They can cause great bodily harm and injury and can
result in death. Always exercise caution when using wireless
keypads. Do not operate keypad to activate a gate or door unless
3
you can see that the area is clear. Always keep children away from
automatic doors and gates.
9
1
1
3
7
3
5
5
(Monday-Friday 6
KG
KG
Chamberlain and Lift-Master are Trademarks of Chamberlain Group. Genie is a
Trademark of Overhead Door Corporation. Linear/Moore-O-Matic is a Trademark of
Linear Corporation. Master Mechanic is a Trademark of TruServe. Multi-Code is a
Trademark of Whistler Corporation. Sears is a Trademark of Sears & Roebuck. Stanley
is a Trademark of Stanley Corporation. Wayne Dalton is a Trademark of Wayne Dalton.
All Rights Reserved
PART 3 – INSTALLATION
AND GENERAL INFORMATION
key.
key again.
TECHNICAL SUPPORT: 800-442-1255
– 7
CST; Saturday 8
AM
PM
- 6
)
AM
PM
Printed in Mexico
Publicidad
