Publicidad
Idiomas disponibles
Idiomas disponibles
by 1 level every 0.4 seconds. When setting "9" is rea-
ched, the setting will not be changed further.
If the setting level has been selected using the MINUS
(2) button, the start level is "9" (maximum level). Keep
the button pressed down to lower the active level by
1 every 0.4 seconds. When setting "0" is reached,
there will be no further setting changed. The setting
can only be changed by pressing the MINUS (2) or
PLUS (3) button again.
Switching a cooking zone off
Select the zone to be switched off using the corres-
ponding button (5). The display (6) of the zone se-
lected lights up, while the remaining displays are
dimmed. Press both the selection button for the co-
rresponding area and the MINUS key (2) at the same
time to set the power level of the area to 0. Alternati-
vely, the MINUS button (2) can be used to reduce the
setting level to 0.
If a cooking zone is "hot", "H" and "0" will be alter-
nately displayed.
Switching all cooking zones off
Press the ON/OFF (1) button to immediately switch
off all zones at any time. In standby mode, an "H"
is displayed in all cooking zones that are "hot". The
remaining displays will be switched off.
Setting level
The cooking zone can be set to 9 levels that are
indicated by the numbers "1" to "9" on the seven-
segment LED displays (6).
Automatic Parboiling
When Automatic parboiling is activated, the power of
the cooking zone is switched to 100 % for a period
of time depending on the selected onboiling stage. As
soon as the parboiling time is over, the preselected
onboiling stage is valid again.
Procedure to start Automatic parboiling:
The control unit is switched on and a cooking zone
is selected.
After setting cooking stage to level "9", press again
the PLUS (3) button.
As a next step, there is a 10 seconds period time to
select the desired cooking stage, by using MINUS (2)
and PLUS (3) buttons.
If a different setting level is then selected, the parboi-
ling function is maintained, and the parboiling time is
adapted to the new selected setting.
Keep Warm Function
This function is available for all cooking areas and
is used to keep food that has already been cooked
warm. It is a power level between level 0 and level 1.
To activate this function, follow these steps:
1. Select the desired cooking area.
2. Select power level 1 using the PLUS button (3)
3. Press the MINUS button (2). The symbol "u" will be
displayed, indicating that the "Keep Warm" function
has been activated.
Residual heat indicator
This informs the user that the glass is at a dange-
rous temperature in the event of touching the area
located around the cooking zone. The temperature is
determined by a mathematical model and any resi-
dual heat is indicated by a "H" on the corresponding
7-segment display.
Heating and cooling are calculated based on:
· The selected setting level (between "0" and "9")
· The ON/OFF time.
After switching off the cooking zone, the correspon-
ding display will indicate "H" until the temperature
in the zone has dropped below the critical level (≤
60°C).
Automatic off function (operating time limita-
tion)
In terms of the setting level, if no operation occurs
each cooking zone switches off after an established
maximum time.
Each operation in the cooking zone condition (using
the PLUS (3) and MINUS (2) or dual zone) restarts the
maximum operating time of the zone by resetting it
to its initial value.
Protection against unintended switching on
· If the electronic control detects a button being held
down for approx. 10 sec. it will switch off automati-
cally. The control sends out an audible error signal
to warn the user that the sensors have detected the
presence of an object. The displays indicate error
code " E R 0 3 ". If the cooking zone is in "hot" mode,
"H" will be indicated alternately on the display with
the error signal.
· If no cooking zone is activated within 20 seconds
after switching on the touch control, it will return to
Publicidad
