Zoeller HOME GUARD MAX 503 Serie Manual De Instalación página 2

Manufacturer warrants, to the purchaser and subsequent owner during
the warranty period, every new product to be free from defects in material
and workmanship under normal use and service, when properly used
and maintained, for a period of two years from date of manufacture.
Parts that fail within the warranty period, that inspections determine to
be defective in material or workmanship, will be repaired, replaced or
remanufactured at Manufacturer's option, provided however, that by
so doing we will not be obligated to replace an entire assembly, the
entire mechanism or the complete unit. No allowance will be made
for shipping charges, damages, labor or other charges that may occur
due to product failure, repair or replacement.
This warranty does not apply to and there shall be no warranty for any
material or product that has been disassembled without prior approval
of Manufacturer, subjected to misuse, misapplication, neglect, alteration,
accident or act of God; that has not been installed, operated or maintained
in accordance with Manufacturer's installation instructions; that has
been exposed to outside substances including but not limited to the
following: sand, gravel, cement, mud, tar, hydrocarbons, hydrocarbon
derivatives (oil, gasoline, solvents, etc.), or other abrasive or corrosive
substances, wash towels or feminine sanitary products, etc. in all
pumping applications. The warranty set out in the paragraph above
In those instances where damages are incurred as a result of an alleged pump failure, the
homeowner must retain possession of the pump for investigation purposes.
1. The system is designed for installation in sumps with minimum
diameter of 18" and depth of 22". For smaller applications,
consult factory.
2. Remove all debris from the pit before installation.
3. Be sure that the pump is clamped securely to the primary pump
discharge pipe and that the two pumps do not interfere with
each other.
1. DO read all installation materials supplied with the pump.
2. DO inspect unit for any visible damage caused by shipping.
Contact dealer if unit appears to be damaged.
3. DO clean all debris from the pit before installation.
4. DO install a union check valve (see STEP 3) in the discharge line.
DO NOT use a discharge pipe smaller than the recommended
pump discharge sizes.
5. DO install a filter or strainer in the water supply line before the
pump to prevent small particles from clogging the operating valve.
6. DO test the pump immediately after installation to be sure that the
system is working properly.
Limited Warranty
Helpful Hints For Easy Installation
Do's And Don't's For Installing A Unit
© Copyright 2012 Zoeller Co. All rights reserved.
is in lieu of all other warranties expressed or implied; and we do not
authorize any representative or other person to assume for us any
other liability in connection with our products.
Contact Manufacturer at, 3649 Cane Run Road, Louisville, Kentucky
40211, Attention: Customer Service Department to obtain any needed
repair or replacement of part(s) or additional information pertaining to
our warranty.
MANUfACTURER EXpRESSLy DISCLAIMS LIABILITy fOR
SpECIAL, CONSEQUENTIAL OR INCIDENTAL DAMAgES OR
BREACH Of EXpRESSED OR IMpLIED WARRANTy; AND
ANy IMpLIED WARRANTy Of fITNESS fOR A pARTICULAR
pURpOSE AND Of MERCHANTABILITy SHALL BE LIMITED TO
THE DURATION Of THE EXpRESSED WARRANTy.
Some states do not allow limitations on the duration of an implied
warranty, so the above limitation may not apply to you. Some states
do not allow the exclusion or limitation of incidental or consequential
damages, so the above limitation or exclusion may not apply to you.
This warranty gives you specific legal rights and you may also have
other rights which vary from state to state.
4. Install a serviceable check valve in the discharge line.
5. Install a filter or strainer in the water supply line before the pump.
Size the filter/strainer properly to minimize pressure drop, while
retaining particles 0.020" (0.5 mm) in diameter and larger.
6. Test the unit immediately after installation. Refer to STEP 5.
7. Check the Float ON/OFF levels per STEP 2 of the instructions.
8. Keep the model number, date code, and installation instructions in
a convenient location for future reference.
7. DO review all applicable local and national codes and verify that
the installation conforms to each of them.
8. DO NOT use the Home Guard
DO NOT use the Home Guard
sewage, effluent, or water with debris in it.
9. DO NOT use a garden hose. Garden hose is not designed to hold
municipal pressure indefinitely and could leak or burst causing
flooding. The Home Guard
method such as copper, PEX, or CPVC.
10. DO install the HomeGuard
2
Max with hot water.
®
Max to remove wastewater,
®
Max requires a permanent piping
®
Max pump with only a ¾" supply line.
®