VTech LS6195 Guía De Inicio Rápida

Quick start guide
LS6195
Introduction
This quick start guide provides you with the basic installation
and setup instructions. A limited set of features are described
in abbreviated form.
You may refer to the Abridged user's manual provided in the
product package for installation and operation instructions, or
see the online Complete user's manual at
www.vtechphones.com for complete installation and
operation instructions.
Telephone base installation
Install the telephone base as shown below.
Telephone wall jack
Electrical outlet
(not controlled by
a wall switch)
Telephone base
power adapter
Telephone base
• Use only the power adapter and battery supplied with
this product.
Battery installation
Install the battery as shown below.
1. Plug the battery
connector securely into
the socket.
THIS SIDE UP / CE CÔTÉ VERS LE HAUT
Battery Pack / Bloc-piles :
(2.4V Ni-MH)
WARNING / AVERTISSEMENT :
NE PAS INCINÉRER OU PERCER LES PILES. DO NOT BURN OR PUNCTURE BATTERIES.
Made in China / Fabriqué en chine
3. Slide the battery
compartment cover
towards the center of
the handset until it clicks
into place.
A DSL filter (not included)
is required if you have
DSL high-speed Internet
service.
The DSL filter must be
plugged into the telephone
wall jack.
Telephone line cord
Enter the handset menu
1. Press MENU.
2. Press
feature menu.
Press SELECT to enter that menu.
3.
• To return to the previous menu, press CANCEL.
To return to idle mode, press and hold CANCEL.
•
2. Place the battery with the
label THIS SIDE UP
up and the wires inside the
battery compartment.
THIS SIDE UP / CE CÔTÉ VERS LE HAUT
Battery Pack / Bloc-piles :
(2.4V Ni-MH)
WARNING / AVERTISSEMENT :
DO NOT BURN OR PUNCTURE BATTERIES. NE PAS INCINÉRER OU PERCER LES PILES.
Made in China / Fabriqué en chine
4. Place the handset in the
telephone base to charge.
CHARGE light
remains on
THIS SIDE UP / CE CÔTÉ VERS LE HAUT when charging.
Battery Pack / Bloc-piles :
(2.4V Ni-MH)
WARNING / AVERTISSEMENT :
DO NOT BURN OR PUNCTURE BATTERIES.
NE PAS INCINÉRER OU PERCER LES PILES.
Made in China / Fabriqué en chine
or until the screen displays the desired
Set date and time
If you subscribe to caller ID service, the day, month and time
are set automatically with each incoming call. You can also
set the date and time manually.
facing
Press MENU.
1.
2. Scroll to Set date/time, then press SELECT.
3. Use the dialing keys (0-9) to enter the month, date and
year, then press SELECT.
4. Use the dialing keys (0-9) to enter the hour and minute.
5. Press or to choose AM or PM, then press SELECT.
Set number of rings
You can choose two, three, four, five or six rings; or toll saver.
With toll saver selected, the answering system answers after
two rings if you have new messages, or after four rings when
there are no new messages. This enables you to check for
new messages and avoid paying long distance charges when
calling from out of your local area.
1. Press MENU.
Scroll to Answering sys, then press SELECT.
2.
3. Scroll to Ans sys setup, then press SELECT.
Scroll to # of rings, then press SELECT.
4.
5. Press or to choose 6, 5, 4, 3, 2 or Toll saver.
Press SELECT.
6.
Record your own announcement with a handset
You can use the preset announcement to answer calls, or
replace it with your own recorded announcement. It can be
up to 90 seconds in length.
1. Press MENU.
Scroll to Answering sys, then press SELECT twice.
2.
3. The handset announces, "To play, press 2. To record,
press 7." Then press 7 to record.
4. The handset announces, "Record after the tone.
Press 5 when you are done." After the tone, speak
towards the handset microphone.
Press 5 when done.
5.
IMPORTANT!
Refer to the online Complete user's manual for a full set of
installation and operation instructions. For manual download or
customer service, visit our website at www.vtechphones.com or
call 1 (800) 595-9511. In Canada, go to www.vtechcanada.com or
call 1 (800) 267-7377.
Copyright © 2012 for VTECH TELECOMMUNICATIONS LTD.
All rights reserved. Printed in China.
96-008690-020-100