Rollplay W421E Manual De Instrucciones página 9

Assembly instructions
1. Assemble the Steering Rod
(1). Place the vehicle upside down on a soft surface and locate the steering
rod hole.
(2). Turn the steering rod to 90, and insert the steering rod into the steering
rod hole.
(3). Insert the screw (24) though the hole located on the shorter end of the
steering rod and through the hole on the car body, fasten the nut (25) to the
end of the screw.
2. Assemble the Shock Absorbers
(1). Take out the screw (19), washer (18), wrench (20) and nut (26) from the
blister pack.
(2). Align the shock absorber (B) with the metal holes.
(3). Insert the screw (19) through the holes. Then slide the washer and screw
nut onto the screw.
(4). Fasten with a screwdriver and wrench.
(5). Repeat steps 1-4 for the other three shock absorbers.
3. Assemble the Front Wheels
(1). Take out the Φ12 front washers (12), Φ10 front/rear washers (13) and
nut (14) from the blister pack.
(2). Slide a Φ12 front washer (12) and front wheel onto the axle.
(3). Slide a Φ10 front/rear washer (13) and wheel nut (14) onto the axle, then
use the hex wrench (15) to tighten.
(4). Snap on the wheel cover by aligning the tabs on the cover with the slots
on the wheel and press until it clicks into place.
(5). Repeat these steps for the other front wheel.
Helpful Tip:
(1). The side of the wheel with rectangular tabs should face outward and the
side marked with an "F" faces inwards.
4. Assemble the Rear Wheels
(1). Take out the washer (13) and screw (14) from the blister pack.
Slide the rear wheel (7) onto the axle. Ensure that the gears on the wheel
connect with the gearbox.
(2). Slide a Φ10 rear washer (13) onto the axle.
(3). Slide a wheel nut (14) onto the axle, and then use the hex wrench to
tighten.
(4). Snap on the wheel cover by aligning the tabs on the cover with the slots
on the wheel.
(5). Repeat these steps for the other rear wheel.
Helpful Tip:
1. If you encounter trouble fitting both wheels onto the rear axle, then your
rear wheel axle may need to be realigned.
2. Remove a wheel from the axle. Pull or push on the axle to slide it until you
have enough room on both sides.
5. Assemble the Exhaust Stack
(1). Place the square piece of the exhaust stack in the square slot on the car
body, then use a screwdriver to secure it with the 4.2 15 bolt (23).
6. Assemble the Steering Wheel
(1). Locate the steering wheel screw (16) and nut (17) from the blister pack
(27).
(2). Align the steering wheel (3) with the steering rod, and insert it into the
rod.
(3). Align the holes on the steering wheel (3) with the holes on the steering
rod.
(4). Insert the steering wheel screw (16) through the steering wheel (3) and
steering rod. Insert the nut (17) into the other side of the steering wheel (3).
(5). Fasten the screw (16) with a screwdriver.
7. Assemble the Brush Guard
(1). Locate the brush guard, 2 M6x48 screws (21), 2 Φ6 washers (27) and 2
M6 nuts (22). The screws and nuts are located in the blister pack.
(2). Align the holes on the brush guard with the holes on the metal frame
under the front bumper.
(3). Insert the Φ6 washers (27) and screws into the holes through the brush
guard and frame, and then secure them with the nuts.
8. Attach the Seat
(1). Make sure the seat lock is turned to the unlocked position.
Slide the tab on the back of the seat into the slot on the car body.
(2). Align the seat over the battery compartment. Ensure the locking mecha-
nism aligns with the hole on the car body. Then slide the seat into position.
(3). Turn the seat lock clockwise until it is in the locked position to properly
secure in place. The image above shows the seat lock in the locked position.
OPERATING INSTRUCTION
9. Steering Wheel Batteries
Steering wheel requires 2 AAA batteries
(1). Open the battery compartment cover with a screwdriver.
(2). Insert the two AAA batteries into the battery compartment.
(3). Replace the battery compartment cover and secure the cover with a
screwdriver.
10. Product Features
Power Button
Push the Power Button to turn the vehicle ON/OFF. The Power Indicator
Light will turn on when the car is on.
Shifter
Pull the Shifter up to move forward. Pull the Shifter down to reverse.
Foot Pedal
Press the Foot Pedal down to move. The vehicle will stop when the Foot
Pedal is released.
Sound Buttons
Press the Sound Buttons on the steering wheel for horn and engine sounds.
High Speed Lock Out
To limit your child's speed while using the vehicle, you can turn on the High
Speed Lock Out feature. Remove the seat and locate the control board
(pictured above). On the bottom corner of the control board is a small switch
to control the speed.
Move the switch to Diagram A's position for high speed, 6.6 km/h (4 MPH).
Move the switch to Diagram B's position to limit the vehicle to low speed,
3 km/h (1.86 MPH).
Please note that the vehicle only travels at 3 km/h (1.86 MPH) when moving
in reverse.
Headlights
The Headlights will turn on automatically when the vehicle is in motion.
CARE
MAINTENANCE
1. Before assembly please check that you have all the parts, if there are any
missing parts please contact your local store.
2. Once assembled please inspect all the parts and ensure the vehicle is
working properly.
3. Please carefully clean the product occasionally and do not destroy any parts.
4. In order to keep your child safe, please inspect and maintain the vehicle
periodically.