Specifications - Campbell Hausfeld NS219001 Instrucciones De Operación

Operating Instructions
The nailer could eject a fastener
causing death or serious personal
injury.
G Protect your eyes
and ears. Wear Z87
safety glasses, with
side shields. Wear
hearing protection.
Employers and users are
responsible for ensuring the user or
anyone near the nailer wears this
safety protection. Serious eye
injury or permanent hearing loss
could result.
G Do not use a
check valve or
any other
fitting which
allows air to
remain in the
nailer. Death or
serious personal injury could occur.
G Never place
hands or any
other body
parts in the nail
discharge area
of the nailer.
The nailer might
eject a fastener and could result in
death or serious personal injury.
G Never carry the
nailer by the air
hose or pull the
hose to move
the nailer or a
compressor. Keep
hoses away from
heat, oil and sharp edges. Replace
any hose that is damaged, weak or
worn. Personal injury or tool
damage could occur.
G Always assume the nailer contains
nails. Never use the nailer as a toy.
Do not engage in horseplay. Always
keep others at a safe distance from
the work area in case of accidental
Nailer Components And Specifications
NS219001
• REQUIRES
(SCFM with 16 nails
per minute @ 90 psi)
• AIR INLET 1/4" NPT
• NAIL LENGTH
RANGE
• NAIL SHANK 0.113" to
RANGE
• MAGAZINE
CAPACITY
• WEIGHT 9 lbs 3 oz
• LENGTH
• HEIGHT
• MAX. PRESSURE
• PRESSURE RANGE 70 - 120 psi
www.chpower.com
discharge of nails. Never point the
nailer at anyone. Accidental
triggering of the nailer could result
in death or serious personal injury.
G Do not drive a
nail on top of
other nails. The
nail could glance
and cause death
or a serious
puncture wound.
G Do not operate
or allow anyone
else to operate
the nailer if any
warnings or
warning labels
are not legible.
Warnings or warning labels are located
on the nailer magazine and body.
G Never leave the nailer unattended or
connected to an air compressor when
not in use. Serious personal injury
can occur if someone picks up and
uses the nailer without knowing the
correct way to operate the nailer.
G Do not drop or throw the tool.
Dropping or throwing the tool can
result in damage that will make the
tool unusable or unsafe. If the tool
has been dropped or thrown,
examine the tool closely for bent,
cracked or broken parts and air
leaks. STOP and repair before using
or serious injury could occur.
a potentially hazardous situation which,
if not avoided, MAY result in minor or
moderate injury.
G Do not modify or alter the nailer or
any nailer parts. Do not use the nailer
if any shields or guards are removed
or altered. Do not use the nailer as a
hammer. Personal injury or tool
damage may occur.
NS219500
4.1 4.1
1/4" NPT
2" to 2" to
1 1
3 ⁄ " 3 ⁄ "
2 2
0.113" to
0.131" 0.131"
60-75 60-75
7 lbs 6 oz
19.25" 19.25"
15.25" 15.25"
120 psi 120 psi
70 - 120 psi
WARNING
!
Caution
indicates
Adjustable Direction Exhaust Deflector
NS319001
NS349001
4.1
1/4" NPT
2" to
1
3 ⁄ "
2
0.113" to
0.131"
75-105
9 lbs 2 oz
18.50"
15.00"
120 psi
Nail Discharge Area
70 - 120 psi
2
G Avoid long extended periods of work
with the nailer. Stop using the nailer
if you feel pain in hands or arms.
G Always
check that
the Work
Contact
Element
(WCE) is
operating
properly. A
nail could
accidentally
be driven if the WCE is not working
properly. Personal injury may occur
(See "Checking the Work Contact
Element" Section).
G Disconnect air supply and release
tension from the pusher before
attempting to clear jams because
fasteners can be ejected from the
front of the nailer. Personal injury
may occur.
important information, that if not
followed, may cause damage to
equipment.
G Avoid using the nailer when the
magazine is empty. Accelerated
wear on the nailer may occur.
G Clean and check all air supply hoses
and fittings before connecting the
nailer to an air supply. Replace any
damaged or worn hoses or fittings.
Tool performance or durability may
be reduced.
G Air compressors providing air to the
nailer should follow the
requirements established by the
American National Standards
Institute Standard B19.3-1991;
Safety Standard for Compressors for
Process Industries. Contact your air
compressor manufacturer for
information.
Trigger
Nail Loading Area
Warning Labels
(Backside)
Debris Shield
Work Contact Element
Notice
indicates
Magazine