Publicidad
Idiomas disponibles
Idiomas disponibles
OPERATING INSTRUCTIONS
Note that the Velo and Velo Pro can be placed in a variety of
positions for drying and air circulation. See Fig. B for details.
1.
Unwrap the cord and plug the unit into a standard 230V
outlet. CAUTION: Be sure switch is in the off position before
connecting unit to power outlet.
2.
Direct the Velo outlet toward the surface to be dried.
3.
Press On switch
4.
When surface is dry to the touch, switch the unit off and
reposition the unit in the next area to be dried.
5.
When finished, unplug the unit and re-wrap the cord in a
counter-clockwise direction around the front and rear cord
wrap tabs and secure with the hook-and-loop provided.
Note: The Velo Pro includes a kilowatt hour meter, useful for
tracking electrical consumption. See Fig. D.
For additional instructions about the use of airmovers for
restorative drying, visit www.DriEaz.com.
Transport and Storage
Always use the handle to load or carry the unit.
Wrap cord in a counter-clockwise direction under front Cord
Wrap tab and rear bottom edge (Fig. A). Pull cord snug and
secure with hook-and-loop tie.
Units may be stacked for transport and storage.
When transporting in a vehicle, secure the unit(s) carefully to
prevent sliding and damage to the unit and/or injury to vehicle
occupants.
Keep unit dry. Do not expose the unit to rain or snow.
Maintenance
WARNING: Unplug unit before performing any maintenance.
Before each use
Inspect the power cord. If cord is damaged, do not use. Always
grasp the plug (not the cord) to unplug.
As needed
Clean housing and impeller. If dust accumulation is visible,
remove the four screws from the top, then turn the unit on its top
and remove the six fasteners from the bottom as shown (Fig. C).
Lift off the housing. Clean impeller assembly with a soft cloth. Do
not apply liquids to the impeller assembly. The housing may be
cleaned with a mild solution of detergent and warm water. Do not
use a hose to clean the unit. Ensure housing is completely dry
before reassembling.
FOR SERVICE CALL YOUR LOCAL DRI-EAZ DISTRIBUTOR or the
Dri-Eaz Service Department at +1 360-757-7776.
07-01851E F504-230V, F505-230V
Fig. C: Disassembly
To disassemble for
cleaning, first remove the
four screws from the
impeller assembly 1)
(below), then turn the unit
on its top and 2) remove
the six screws from the
base. Lift off the housing.
Retain screws and
washers for reassembly.
1. Remove impeller
assembly screws (×4).
Fig. D: Pro model only: Kilowatt Hour
meter
SPECIFICATIONS
Model
Velo (F504-230V)
Weight
9.52 kg
Dimensions
61 × 45.7 × 22.9 cm
(D × W × H)
Amp draw
.54 amps (230V)
Power
124W
Max. Airflow
1190 m
RPM
1280
Rotation
Clockwise
Static pressure
28 mm (H
Sound level (avg.)
65 dB
Control
On/Off switch
Cord length
4.6 m
Fan
6 blades
Kickstand
No
Kilowatt Hour
No
Meter
Rotomolded
polyethylene and
injection molded ABS
Construction
housing components;
steel wire inlet and
outlet grills.
Safety
CE
Specifications are subject to change without notice. Some values
may be approximate.
2
2. Remove base
screws (×6) and
lift out housing.
Velo Pro (F505-230V)
9.52 kg
61 × 45.7 × 22.9 cm
.54 amps (230V)
124W
3
3
/h
1190 m
/h
1280
Clockwise
O)
28 mm (H
O)
2
2
65 dB
On/Off switch
4.6 m
6 blades
Yes
Yes
Rotomolded
polyethylene and
injection molded ABS
housing components;
steel wire inlet and
outlet grills.
CE
Dri-Eaz Products, Inc.
Publicidad
