Pompco S-275 SS Manual Del Proprietário página 4

DESCRIPTION
95 711-0050 RV-50 / 100 PSI RELIEF VALVE
522-3512 STAINLESS STEEL CUTTER PIN
522-0175 S-275 FRONT ASS'Y
522-0185 S-600 FRONT ASS'Y
522-2850 S-275 REPAIR KIT
522-2852 S-600 REPAIR KIT
WATER TYPICAL PISTON PUMP INSTALLATION WITH GALVANIZED TANK
INSTALLATION TYPIQUE D'UNE POMPE À PISTON POUR L'EAU AVEC RESERVOIR GALVANISE
INSTALACIÓN TÍPICA BOMBA DE PISTONES PARA AGUA CON TANQUE GALVANIZADO
PITLESS ADAPTOR
COULISSEAU
CURSOR DE AJUSTE
FOOT VALVE
CLAPET DE PIEDS
VALVULA DE PIE
-THE SNIFER VALVE IS NOT INCLUDED WITH THE STAINLESS STEEL PUMP. MUST BE
PURCHASE SEPARATLY.
-LE RENIFLARD N'EST PAS INCLUS DANS LA POMPE EN ACIER INOXIDABLE. PEUT ÊTRE
ACHETE SEPAREMENT.
-LA VALVULA DE ALIVIO NO ESTA INCLUIDA CON LA BOMBA DE ACERO INOXIDABLE,
DEBERA SUMINISTRARSE POR SEPARADO.
THE STAINLESS STEEL PISTON PUMP CAN BE USED TO PUMP
LA POMPE EN ACIER INOXIDABLE PEUT ETRE AUSSI UTILISÉE
POUR LE SIROP D'ÉRABLE.
LA BOMBA DE PISTON EN ACERO INOXIDABLE PUEDE USARSE
PARA BOMBEAR JARABE DE MAPLE.
DESCRIPTION DESCRIPCIÓN
SOUPAPE DE SÉCURITÉ RV-50 / 100 PSI Válvula de alivio RV-50 / 100 PSI
GOUPILLE FENDUE EN ACIER INOX. Pasador de Acero Inox.
S-275 S/S DEVANT ASSEMBLE S-275 S/S DELANTE ENSAMBLADO
S-600 S/S DEVANT ASSEMBLE S-600 S/S DELANTE ENSAMBLADO
NÉCESSAIRE DE RÉPARATION S-275 Estuche de reparaciones S-275
NÉCESSAIRE DE RÉPARATION S-600 Estuche de reparaciones S-600
ELECTRICAL ENTRY
ENTRÉE ÉLECTRIQUE
ENTRADA ELÉCTRICA
ELECTRICAL DISCONNECT
SÉLECTIONNEUR ÉLECTRIQUE
SELECTOR ELÉCTRICO
GALVANIZED TANK
RÉSERVOIR GALVANISÉ
TANQUE GALVANISADO
AIR VOLUME CONTROL
CONTRÔLE DE VOLUME D'AIR
CONTROL DE VOULMEN DE AIRE
TANK TEE
PISTON PUMP TÉ RÉSERVOIR
TEE PARA TANQUE
POMPE À PISTON
SNIFTER VALVE
BOMBA PISTONES
RENIFLARD
VALVULA DE AIR
MAPLE SYROP
PISTON PUMP INSTALLATION INSTRUCTIONS
IMPORTANT: Read carefully this instruction manual before installing or operating the pump.
Read with attention the security warning messages.
ATTENTION:
⇒ Read instructions before operating the pump.
⇒ The electrical installation must be in accordance with the Local guide of electricity and with all other
applicable local codes and rules.
WARNING - ELECTROCUTION RISK:
⇒ Call upon a qualified electrician for the motor's electrical supply.
⇒ Make sure that the motor is correctly grounded and that all connections are safe and watertight.
⇒ Before proceeding with the maintenance of the pump, always shut down the motor's electrical supply.
1) Unscrew the plug (#94) on the pump body and fill pump body with 7 ounces (200 ml) of SAE-
30 oil, filler hole location is indicated by arrow on the window.
2) Choose a location for your pump as close as possible to the water supply.
recommended to install a suction pipe of 1 ¼" (minimum). Piping should be arrange with
a gradual incline to the water source, without links.
3) Install foot valve assembly on the suction line, and place line into well below the water level.
• Remove the priming plug (#89) from the air chamber
• Fill water box
• Put the priming plug back in its place
• Start the pump.
The pump should be now in normal operation
VALVE
SOUPAPE
VALVULA
1) Periodically check the oil level in the pump body.
2) Slightly tighten the packing retainer nut (#75) .
3) For replacement parts and repair kits contact your local dealer or the manufacturer if a dealer
is not available.
If your pump is not to be operated during winter, carefully follow the present instructions for
draining pump. You will then eliminate the possibilities of cracking the water box that could be
caused by freezing :
• Remove primer plug (#89)
• Remove drain plugs (#94) located under water bos (#88)
• Start and run pump for a few seconds to completely drain.
Suction and discharge lines should be removed for storage.
PROBLEMS
Motor rumbles but do not start.
Motor stops and starts too often Check: a) Not enough air in tank b) Air valve blocked.
Air is discharged with water.
Overheating motor.
Pump does not maintain loaded
No water in tank.
Low pressure.
SECURITY - DANGER
Start up
Priming
Maintenance
Winterizing
TROUBLE SHOOTING
Check : a) Voltage b) Tension of packing box nut c) Tension on ''V'' belt
Air/water ratio incorrect, too much air in tank or using of diaphragm tank.
Check : a) Air valve operation b) Leak in suction pipe or packing box
c) Water level lower than suction line, add pipe if 25 feet (7,62m) of vertical
line is not already used
Check : a) Wiring b) ''V'' belt tension
Check : a) Foot valve b) Piping c) Water level in well d) Dirt under
rubber valve
Check: a) Leak b) the water level it must always be above the foot valve.
Check : a) Piston leather b) Dirt under rubber valve
Replace parts if necessary.
It is