Lutron Electronics Pico wireless control PRO Instrucciones De Instalación Y Manual De Operación

Pico 4-Button
®
Wireless Control
3 V- 10 mA
Mounting accessories sold separately.
For a complete listing of Pico wireless mounting
®
accessories and more information about Pico
controls, please visit www.lutron.com/pico
P/N 041481 Rev. A
PJ2-4B
11/2014
Important Notes
Please Read Before Installing
1. This install guide provides simple setup instructions for Maestro
Wireless and Caséta Wireless systems only. If you are using your
® TM
Pico wireless control with any other Lutron system, please refer
® ®
to the system setup guide. If you no longer have your system setup
guide, please download the latest version by following the links at
www.lutron.com
2. The Pico wireless control uses one (1) CR2032 battery
®
(pre-installed). DO NOT use rechargeable batteries. Using improper
batteries could damage the Pico wireless control. DO NOT
®
dispose of the battery in normal household waste. Please recycle,
take to a proper battery disposal facility, or contact your local waste
disposal provider regarding local restrictions on the disposal or
recycling of batteries.
WARNING: Risk of fire, explosion and burns. May result
in serious injury or death. DO NOT recharge, disassemble,
crush, puncture, heat above 212 °F (100 °C) or incinerate
the battery. The battery in this device contains Perchlorate
Material — special handling may apply. For more information.
visit www.dtsc.ca.gov/hazardouswaste/perchlorate
3. The Pico wireless control must be paired with dimmer(s) / switch(es)
®
before it can communicate.
4. Up to 10 Pico wireless controls can be configured to work together
®
in a Maestro Wireless system or with a stand-alone Caséta
®
Wireless dimmer / switch.
5. The range of the Pico wireless control is 30 ft (9 m). Performance is
®
highly dependent on a variety of complex factors, such as:
• Distance between system components
• Geometry of the building structure
• Construction of walls separating system components
• Electrical equipment located near system components
6. Clean Pico wireless control with a soft damp cloth only.
®
7. DO NOT paint the Pico wireless control.
®
8. DO NOT mount the Pico wireless control to a metal surface.
®
FCC / IC Information
This device complies with part 15 of the FCC Rules and Industry Canada license-exempt RSS
standard(s). Operation is subject to the following two conditions:
(1) This device may not cause interference, and
(2) this device must accept any interference, including interference that may cause undesired
operation. Modifications not expressly approved by Lutron Electronics Co., Inc. could void the user's
authority to operate this equipment.
Note: This equipment has been tested and found to comply with the limits for a Class B digital device,
pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection
against harmful interference in a residential installation. This equipment generates, uses and can
radiate radio frequency energy and, if not installed and used in accordance with the instructions, may
cause harmful interference to radio communications. However, there is no guarantee that interference
will not occur in a particular installation. If this equipment does cause harmful interference to radio
or television reception, which can be determined by turning the equipment off and on, the user is
encouraged to try to correct the interference by one or more of the following measures:
• Reorient or relocate the receiving antenna
• Increase the separation between the equipment and receiver
• Connect the equipment into an outlet on a circuit different from that to which the receiver is
connected
• Consult the dealer or an experienced radio / TV technician for help
Lutron Electronics Co., Inc.
7200 Suter Road
Coopersburg, PA 18036-1299
English
Set-Up
(for Maestro Wireless and Caséta Wireless systems only)
® TM
To communicate with other systems or devices, including
RadioRA 2, HomeWorks QS, QS sensor module (QSM),
® ®
Quantum , Serena Shades, and Sivoia
® ®
setup guides.
wireless
®
Important: Set up a Pico wireless control to a dimmer / switch
®
before use.
1. Press and hold the dimmer / switch Tap button or Off button
(Figure 1) for approximately 6 seconds. Once the LED(s) start to
blink slowly, release the Tap or Off button.
2. Press and hold the Off button on the Pico
(Figure 2) for approximately 6 seconds.
Note: For 2-group Pico wireless controls only, pair the second
®
group by repeating steps 1 and 2 using the Off button of the
second grouping (Figure 3c).
Figure 1
Maestro Wireless Caséta
®
Dimmer / Switch Dimmer / Switch
3. Once the dimmer / switch pairs with the Pico
LED(s) on the dimmer / switch and the load will flash 3 times and
they will exit Set-Up mode.
4. Repeat steps 1– 3 to pair multiple Pico
single dimmer / switch. Repeat steps 1– 3 to pair a single Pico
wireless control with multiple dimmers / switches.
Notes
• Zone Control and 2-Group Control: Pairing with multiple
TM
dimmers / switches will cause each dimmer / switch to have the
same response to each button press of the Pico
control.
• Scene Control: Each dimmer / switch can be set to unique levels
for a personalized effect. For more information, see Scene Control
Operation.
Replacing the Battery in a Pico
1. Place a flathead screwdriver into the slot at the bottom of the Pico
wireless control. Twist to open. DO NOT press buttons without
back enclosure on.
2. Slide the battery out, toward the top of the Pico
3. Slide a new battery underneath the contact strap, with the (–)
terminal toward the front of the Pico
®
4. Replace the back enclosure.
5. Confirm proper installation by turning the receiving device ON and
OFF using the Pico wireless control.
®
Lutron, ), HomeWorks, Maestro Wireless, Pico, Quantum, RadioRA, Serena, and Sivoia are registered trademarks and Caséta and RadioRA 2 are trademarks of Lutron Electronics Co., Inc.
© 2014 Lutron Electronics Co., Inc.
Operation
Indicator LED
Flashes to indicate a
QS, refer to the system
® button press or when unit
is in programming mode.
Zone Control
wireless control
®
Figure 2
Figure 3a
Scene Control Operation (Figure 3b)
Wireless Pico
TM ® Scene Recall
Wireless Control
Pressing a Scene button on a Scene control will cause all dimmers to go
to the Scene settings. Switches can be configured to turn ON or OFF.
wireless control, the
®
Scene Saving
Adjust all of the dimmers / switches controlled by a Scene control to the
wireless controls with a desired light setting. Then press and hold a Scene button on the control
®
for 6 seconds until all LEDs on the dimmers / switches flash several times.
®
Locking / Unlocking Scene Levels (for Maestro Wireless
Caséta Wireless, and GRAFIK Eye
TM
• To lock the Scene settings, press and hold the top two buttons for
approximately 3 seconds. The Scene settings cannot be changed while
4-Button wireless
locked.
®
• To unlock the Scene settings, simultaneously press and hold the top
two buttons for approximately 3 seconds. The Scene settings may be
changed while unlocked.
Wireless Control
®
®
wireless control.
®
wireless control.
Troubleshooting
Symptoms
Light does not respond to Pico
control
When in set-up mode, the LEDs on the
dimmer / switch flash when trying to set up
with the Pico wireless control or sensor
®
Cannot save scene
Scene settings change unexpectedly
Scene Control
Default Light Levels
Button 1: 100%
On Button
Button 2: 66%
Lights brighten ON to full
Button 3: 33%
intensity.
Button 4:
Raise Button
Lights increase in intensity. Scene Buttons
Tap once: Sends device to
preset levels.
Lower Button Press and hold for
Lights decrease in intensity. 6 seconds: Saves new
scene.
Off Button Off Button
Lights dim to OFF. Lights dim to OFF.
Figure 3b
,
®
QS systems only)
®
Possible Causes
wireless • The dimmer / switch failed to pair with Pico
®
• The dimmer / switch has already received and responded to a command or is already at the light
setting the Pico wireless control is sending.
®
• The Pico wireless control is outside the 30 ft (9 m) operating range.
®
• The battery in the Pico wireless control is low.
®
• The battery in the Pico wireless control is installed incorrectly.
®
• The maximum number of Pico
®
dimmer / switch. More Pico wireless controls or sensors cannot be added. See Un-pairing a
®
Pico Wireless Control.
®
• Scene settings are locked. See Locking / Unlocking Scene Levels.
• Scene settings are unlocked. See Locking / Unlocking Scene Levels.
2-Group Control
Group 1:
On Button #1
Lights brighten ON to full
0
intensity.
Off Button #1
Lights dim to OFF.
Group 2:
On Button #2
Lights brighten ON to full
intensity.
Off Button #2
Lights dim to OFF.
Figure 3c
Un-pairing a Pico Wireless Control
®
(for Maestro Wireless and Caséta Wireless systems only)
® TM
• To un-pair a previously paired Pico wireless control from
®
your system, tap the Off button (Figure 2) on the Pico
wireless control three times; on the third tap, hold for
6 seconds and then tap three more times. This will remove all
dimmers / switches with which it was previously paired.
Technical Assistance www.lutron.com
World Headquarters
For questions concerning the installation or operation of this product,
call the Lutron Technical Support Center. Please provide exact model
number when calling.
TEL: +1.610.282.3800
FAX: +1.610.282.1243
Toll Free:1.888.LUTRON1
USA, Canada, Caribbean: 1.800.523.9466
Mexico: +1.888.235.2910
Central / South America: +1.610.282.6701
wireless control; see Set-Up.
®
wireless controls or sensors has been paired with the
®
®