Ryobi PBC-3046YB Manual De Utilización página 24

PBC-3046YB manual
GB
F D E
GENERAL SAFETY RULES
a) Keep your body warm in cold weather. When
operating the unit wear gloves to keep the hands
and wrists warm. It is reported that cold weather is
a major factor contributing to Raynaud's Syndrome.
b) After each period of operation, exercise to increase
blood circulation.
c) Take frequent work breaks. Limit the amount of
exposure per day.
d) Keep the tool well maintained, fasteners tightened
and worn parts replaced.
If you experience any of the symptoms of this
condition, immediately discontinue use and see your
physician about these symptoms.
Mix and store fuel in a container approved for gasoline.
■
Mix fuel outdoors where there are no sparks or
■
flames. Wipe up any fuel spillage. Move 9 m (30 ft.)
away from refueling site before starting engine.
Stop the engine and allow to cool before refueling or
■
storing the unit.
Allow the engine to cool; empty the fuel tank and
■
secure the unit from moving before transporting in
a vehicle.
SPECIFIC SAFETY RULES FOR TRIMMER USE
Replace string head if cracked, chipped, or damaged
■
in any way. Be sure the string head or blade is
properly installed and securely fastened. Failure to do
so can cause serious injury.
Make sure all guards, straps, deflectors and handles
■
are properly and securely attached.
Use only the manufacturer's replacement string
■
in the cutting head. Do not use any other cutting
attachment.
Never operate unit without the grass deflector in
■
place and in good condition.
Maintain a firm grip on both handles while trimming.
■
Keep string head below waist level. Never cut with
the string head located over 76 cm (30 in.) or more
above the ground.
SPECIFIC SAFETY RULES FOR
BRUCHCUTTER AND BLADE USE
After engine stops, keep rotating blade in heavy grass
■
or pulpy weeks until it stops.
Do not operate the brushcutter unless the blade
■
guard is firmly secured in place and in good condition.
10/01/05 9:29 Page 17
I P NL S
English
DK N FIN GR H
Use heavy gloves while installing or removing blades.
■
Always stop the engine and remove the spark plug
■
wire before attempting to remove any obstruction
caught or jammed in the blade or before removing
and installing the blade.
Do not attempt to touch or stop the blade when it is
■
rotating.
A coasting blade can cause injury while it continues to
■
spin after the engine is stopped or throttle trigger
released. Maintain proper control until the blade has
completely stopped rotating.
Replace any blade that has been damaged. Always
■
make sure blade is installed correctly and securely
fastened before each use. Failure to do so can cause
serious injury.
Use only the manufacturer's replacement TRI-ARC
■
blade intended for use on this brushcutter. Do not use
any other blade.
The TRI-ARC blade is suited for cutting pulpy weeds
■
and vines only. Do not use for any other purpose.
Never use the TRI-ARC blade to cut woody brush.
Exercise extreme caution when using the blade with
■
this unit. Blade thrust is the reaction that may occur
when the spinning blade contacts anything it cannot
cut. This contact may cause the blade to stop for an
instant, and suddenly "thrust" the unit away from the
object that was hit. This reaction can be violent enough
to cause the operator to lose control of the unit.
Blade thrust can occur without warning if the blade
snags, stalls, or binds. This is more likely to occur in
areas where it is difficult to see the material being cut.
For cutting ease and safety, approach the weeds
being cut from the right to the left. In the event an
unexpected object or woody stock is encountered,
this could minimize the blade thrust reaction.
Never cut any material over 13 mm (1/2 in.) diameter.
■
Always wear the shoulder strap when using the
■
brushcutter and adjust to a comfortable operating
position. Maintain a firm grip on both handles while
cutting with a blade. Keep the blade away from body
and below waist. Never use the brushcutter with the
blade located 76 cm (30 in.) or more above the
ground level.
Cover the blade with the blade protector before
■
storing the unit, or during transportation. Always
remove the blade protector before using the unit.
If not removed, the blade protector could become a
thrown object as the blade begins to turn.
17
CZ RUS RO PL