Campbell Hausfeld PT281303 Instrucciones De Operacion Y Lista De Partes página 2

Operating Instructions and Replacment Parts List
General Safety Information
(Continued)
3. Do not pressurize tank over 50 psi.
4. Do not exceed the pressure rating
of any component in the system.
5. Be certain that pressure regulator
and safety valve are clean and in
proper working order before using
the paint tank.
6. Be certain that the air supply line is
at zero psi and pressure regulator is
turned off before connecting tank
to air supply.
7. Make sure all feed line, eyebolts
and spray guns are secure before
turning air supply on.
8. Release all pressure within the
system before attempting to service
any component.
9. Protect material lines and air lines
from damage or puncture.
10. Never point a spray gun at yourself
or at any other person. Accidental
discharge may result in serious
injury.
11. Check hoses for weak or worn
condition before each use, making
certain that all connections are
secure.
12. Always shut off air pressure at
source and bleed off all pressure in
paint tank by gently pulling safety
valve ring before loosening knobs.
13. Regularly check to be sure gauge
and regulator are functioning
correctly. Also check that no paint
or other deposits are in the safety
valve inlet. In the event more than
50 psi is applied to the tank and the
safety valve is clogged, the higher
pressure could damage the tank or
result in injury.
Do not spray flammable
materials in vicinity of open
flame or near ignition
sources including the
compressor unit.
14. Do not smoke when spraying paint,
insecticides, or other flammable
substances.
www.chpower.com
15. Use a face mask /
respirator when spraying
and spray in a well
ventilated area to prevent
health and fire hazards.
16. Do not direct paint or other sprayed
material at the compressor. Locate
compressor as far away from the
spraying area as possible to
minimize overspray accumulation
on the compressor.
17. When spraying or cleaning with
solvents or toxic chemicals, follow
the instructions provided by the
chemical manufacturer.
Failure to follow instructions on proper
assembly and use of a paint tank may
possibly result in damage to property
or personal injury. This unit must be
assembled as indicated in these
instructions. Only parts supplied with
this unit should be used. These parts
are safety performance engineered. Use
only OEM replacement components.
Assembly
NOTE: Use Teflon ® tape or thread
sealant on all connections.
1. Assemble the regulator to the paint
tank lid as shown in Figure 1:
Pressure gauge
Pipe nipple
Figure 1
a. With arrow pointed down and
knob toward you, place the
gauge in the left 1/8 NPT
regulator port.
b. Assemble the 1/8 plug into
opposite 1/8 NPT regulator port.
c. Thread the 1/4 T-fitting into the
top 1/4 inch regulator port.
d. Thread 1/4 inch pipe nipple into
bottom 1/4 inch regulator port
(with arrow).
e. Thread this assembly into the #3
1/4 NPT port on tank lid.
2
Handle
Safety
relief
valve
Material
tube
Figure 2
NOTE: This regulator is a special
pressure limiting regulator. Do not use
any other type of regulator with this
paint tank. Assemble the regulator to
the paint tank only as instructed.
2. Assemble the safety relief valve to
the tank lid port #4.
3. Install the pipe plug into the 1/8
NPT port #2 of the tank lid.
4. Thread the handle into the center
port of the tank lid.
5. Install hose connector in tank lid
port #1 from the top.
6. The material tube is pre-assembled
to port #1.
7. To assemble tank bracket with knob
assembly:
a. Lay out tank bracket to form
circle (4 sections).
b. Insert eyebolt between each
section, slip hex bolt through
holes and loosely screw on stop
nuts.
c. Flip tank upside down and slip
bolted bracket assembly around
tank.
d. Slide bracket down to rim and
tighten all nuts.
Air
IN
Hose connectors
Figure 3
Hose
connector
Pipe plug
Air OUT to
spray gun
(unregulated)