Outlet For The Extraction Pipe; Left Side Outlet; Rear Outlet; Right Side Outlet - Brandt ETE 762K Guía De Utilización

Outlet for the extraction pipe

The flexible pipe is designed to extract moist air from your drier. There are three possible
outlets:
L L e e f f t t s s i i d d e e o o u u t t l l e e t t
R R e e a a r r o o u u t t l l e e t t
R R i i g g h h t t s s i i d d e e o o u u t t l l e e t t
On delivery, the outlet on your machine is
on the left side (Fig. 1)
.

Left side outlet:

- Remove the bung on the left side
- Unclip the knob by pulling it outwards;
then release the extraction pipe.
(Fig. 1)

Rear outlet:

- Follow the actions shown in the drawings
(Figs. 2 and 3)
- Bring the extraction pipe out through the
hatch opening.

Right side outlet:

- Re-insert the left bung
- Pass the pipe assembly and the knob
through the panel. Adjust the knob to
do this (Fig. 4)
O O n n c c e e y y o o u u h h a a v v e e c c o o m m p p l l e e t t e e d d t t h h e e a a b b o o v v e e
o o p p e e r r a a t t i i o o n n s s : :
- - C C o o n n n n e e c c t t t t h h e e e e x x t t r r a a c c t t i i o o n n p p i i p p e e t t o o t t h h e e w w a a l l l l
C C e e r r t t a a i i n n p p r r e e c c a a u u t t i i o o n n s s a a r r e e n n e e c c e e s s s s a a r r y y w w h h e e n n i i n n s s t t a a l l l l i i n n g g t t h h e e e e x x t t r r a a c c t t i i o o n n p p i i p p e e : :
T T h h e e p p i i p p e e m m u u s s t t n n o o t t b b e e s s t t r r e e t t c c h h e e d d
T T h h e e r r e e m m u u s s t t b b e e a a s s f f e e w w b b e e n n d d s s a a s s p p o o s s s s i i b b l l e e i i n n t t h h e e p p i i p p e e ( ( m m a a x x i i m m u u m m 2 2 ) )
F F o o l l l l o o w w i i n n g g t t h h i i s s a a d d v v i i c c e e w w i i l l l l e e n n a a b b l l e e y y o o u u t t o o o o b b t t a a i i n n b b e e t t t t e e r r d d r r y y i i n n g g r r e e s s u u l l t t s s . .
Fig. 1
Fig. 2
Fig. 3
Fig. 4
6

Installing your drier

Your drier's surroundings:

Your drier gives out heat. If you install
it next to another machine or a unit, we
recommend that you always leave a gap
to allow air to circulate (Fig. 6).
We also strongly recommend that you:
- Do not install your machine on a carpeted
floor.
If this should prove unavoidable, take every
precaution to avoid obstructing the
circulation of air around the machine's base.
- Do not install your machine in an area
where it may be subject to being splashed
with water.
- Do not install your drier in a small closed
room (if this should be the case, open the
door or the window during drying).

Levelling:

Check that the floor is horizontal using a
spirit level: maximum permissible slope =
1.5°, i.e. a discrepancy of approx. 1cm over
the machine's width and depth.
Your drier is fitted with 4 adjustable feet
(Fig. 7).
To level it and ensure its stability:
- Tilt it backwards slightly
- Screw or unscrew one or more of the feet
using a spanner or pliers to adjust their
height to suit the configuration of the floor
(Fig. 7)
- Set your drier back on its feet and check
its stability.
- Do not install your machine in a poorly
ventilated room: the room's temperature
during drying must be less than 30°C
Fig. 6
Fig. 7
7