Location Of Controls; Power Connection; Listening To Radio - FIRST AUSTRIA FA-2420 Manual De Instrucciones

INSTRUCTION MANUAL
PROJECTION ALARM CLOCK RADIO

LOCATION OF CONTROLS

(see fig. 1)
1. PROJECTION ON/OFF
2. PROJECTION TIME 180°
3. SNOOZE/SLEEP/DIMMER
4. ON – OFF RADIO/SOURCE/ALARM
OFF
5. DISPLAY
6. ALARM 2 INDICATOR
7. RATING LABEL
(BOTTOM OF UNIT)
8. STANDBY INDICATOR
9. ALARM 1 INDICATOR
10. MEMORY/MEMORY+/CLK.ADJ./NAP
WARNING
DO NOT INGEST BATTERY, CHEMICAL BURN HAZARD
This product contains a coin/button cell battery. If the coin/button cell battery is
swallowed, it can cause severe internal burns in just 2 hours and can lead to death.
Keep new and used batteries away from children. If the battery compartment does not
close securely, stop using the product and keep it away from children.
If you think batteries might have been swallowed or placed inside any part of the body,
seek immediate medical attention.

POWER CONNECTION

Connect the cord of the power adapter to the DC IN jack of the radio.
Connect the plug of the power adapter to a wall socket. The radio is powered and in
standby mode when you see the display is switched on.
This unit is equipped with a battery back up system, it requires a 1x3V CR2032 Flat
Lithium battery (Not included). Insert the battery in the battery compartment, making
certain that the positive and negative (+ and -) battery terminals are attached to the
corresponding terminals on the plate in the battery compartment. If an AC power failure
occurs, the clock automatically switches to the battery power supply, the clock and timer
memory continue running. When the AC power resumes, the clock switches back to AC
again.
When replacing the battery, do not disconnect the power adapter. Otherwise, all clock
and alarm settings will be lost.
GETTING STARTED
TIME AND CALENDAR MANUAL SETTING
Press CLK.ADJ. button (10), in standby mode, and keep depress over 3 seconds to
enter time set mode, after enter the setting mode, press CLK.ADJ button (10) to change
the mode cycle as follows:
Normal → Year → Month → Day → 24H → Real time Hour → Real time Min → Normal
Action (during data adjustment):
• Press <</Tune- button (11) to adjust data backward.
• Press >>/Tune+ button (12) to adjust data forward.
• Keep depress << or >> button for 3 seconds to enable auto forward.
11. <</TUNE -/YEAR/MONTH/DAY/
DISPLAY AUTO CHANGE ON-OFF
12. >>/TUNE +/AUTO ON-OFF DISPLAY
13. VOLUME DOWN/ALARM 1 ON-OFF
SET
14. VOLUME UP/ALARM 2 ON-OFF SET
15. SPEAKER
16. FOCUS ADJUSTMENT FOR
PROJECTION UNIT
17. FM ANTENNA
18. BATTERY COMPARTMENT
19. DC IN JACK
20. USB CHARGING PORT
2
ALARM
SETTING ALARM
Press the alarm set button (13/14) during normal mode to show the alarm time.
Afterwards keep depress the alarm set button (13/14) over 2 seconds to enter the alarm
set mode. After enter the setting mode, press the alarm set button (13/14) to change the
mode cycle as follows :
Normal → AL 1 Hour → AL 1 Min → AL 1 weekday Alarm → AL 1 wake beep → AL 1
wake radio →nature sound → select the nature sound mode (n-1, n-2, n-3, n-4, n-5, n-6
shows on the display) → AL 1 wake volume → Normal.
Normal → AL 2 Hour → AL 2 Min → AL 2 weekday Alarm → AL 2 wake beep → AL 2
wake radio →nature sound → select the nature sound mode (n-1, n-2, n-3, n-4, n-5, n-6
shows on the display) → AL 2 wake radio volume → Normal.
Select alarm weekday mode as follows
1-5: Monday to Friday
1-7: Whole week
6-7: Saturday & Sunday
1-1: One day of week
Action (during data adjustment):
• Press <</Tune- button (11) to adjust data backward.
• Press >>/Tune+ button (12) to adjust data forward.
• Keep depress << or >> button for 2 seconds to enable auto forward.
ENABLE/DISABLE THE ALARM
Press and hold the "ALARM 1" (13)/"ALARM 2" (14) button to enable or disable the
alarm. Once the alarm is activated, the bell symbol will be appeared on the display.
ALARM DURATION AND SNOOZE FUNCTION:
Alarm Duration – Beep alarm or radio alarm will continue output for 60 minutes if no key
press, then it will stop automatically and wait for same alarm time on next day.
Action for Snooze:
• During alarming, press Snooze button (3) will enable snooze function, Beep alarm or
Radio alarm will stop.
• Snooze interval is 9 minute (not include second offset)
• Snooze will continue unless press ON/OFF button (4) to alarm off of Buzzer alarm or
Radio Alarm stop automatically after 60 minutes.
Display Auto on-off function:
• Press & hold the display auto on-off button (12) for 3 seconds, the LED display
Indicator will light on, the LED display will turn off after 15 seconds automatically.
Press any button to maintain the LED display for 15 seconds.
• Press & hold the display auto on-off button (12) for 3 seconds, the LED display
Indicator will light off to cancel this function.
AUTO CHANGE DISPLAY CONTENT (see fig. 2)
In radio off mode, press the DISPLAY AUTO CHANGE ON/OFF (11) button and keep
depressed over 3 seconds to enter time AUTO CHANGE DISPLAY mode. The Year will
be displayed and press again to display Month/Day, the display returns to time display
after 5 seconds.

LISTENING TO RADIO

Press the ON/OFF button (4) to turn the unit on.
Use the Tune+ or Tune- button to select the desired station. If you press and hold the
Tune+ or Tune- button for one second, the release, the unit will automatically scan to the
next broadcasting station.
Press the ON/OFF button (4) to turn the radio OFF.
3