Tabla de contenido
Resumen de contenidos para Sanus VuePoint FPA400
- Página 1 FPA400 INSTRUCTION MANUAL We’ll Make It Stress-Free If you have any questions along the way, just give us a call. 1-888-333-9952. We’re ready to help! Scan for easy install video san.us/260...
-
Página 2: Before You Begin
IMPORTANT SAFETY INSTRUCTIONS – SAVE THESE INSTRUCTIONS – PLEASE READ ENTIRE MANUAL PRIOR TO USE Before You Begin Please check the following items: Any accessories you plan to use do not exceed the specifi ed weight limit. The wall you chose to mount your shelf is wood stud, drywall, solid concrete, or concrete block. You read and understand these directions. -
Página 3: Weight Limit
Weight Limit Tools Needed 15 lb (6.8 kg) DO NOT EXCEED! Features Can be mounted to drywall, wood stud, or concrete. Stackable to accommodate multiple components - not to exceed 15 lb (6.8 kg) on each shelf. 3 mm 10 mm 10 mm (1/8 in.) (3/8 in.) - Página 4 Supplied Parts and Hardware WARNING: This product contains small items that could be a choking hazard if swallowed. Before starting assembly, verify all parts are included and undamaged. If any parts are missing or damaged, do not return the damaged item to your dealer;...
- Página 5 Dimensions Stacked confi guration Single shelf confi guration [mm] 12.50 12.50 317.5 317.5 17.00 17.00 431.8 431.8 1.11 28.1 1.11 28.1 159.9 159.9 5.11 129.8...
- Página 6 STEP 1 Attach the Wall Plate to the Wall - Wood Stud Option IMPORTANT: For stacking configurations, stack from the top down. Locate your stud(s). Verify the center of the stud using an awl, a thin nail, or an edge to edge stud finder. CAUTION: Avoid potential personal injuries and property damage! ●...
- Página 7 STEP 1 Drill pilot holes. IMPORTANT: Pilot holes must be drilled to a depth of 63.5 mm (2½ in.), using a 3 mm (1/8 in.) diameter drill bit. Tighten the lag bolt and washer the screw only until they are pulled firmly against the wall plate CAUTION: Improper use could reduce the holding power of the lag bolt and screw.
- Página 8 STEP 1 Attach the Wall Plate to the Wall - Solid Concrete or Concrete Block Option IMPORTANT: For stacking configurations, stack from the top down. Remove the front (F) and top (T) covers from the wall plate Level the wall plate and mark the hole locations.
- Página 9 STEP 1 Insert anchors CAUTION: Be sure the anchors are seated flush with the concrete surface. Tighten the lag bolt and washer the screw only until they are pulled firmly against the wall plate CAUTION: Improper use could reduce the holding power of the lag bolt and screw. DO NOT over-tighten the lag bolt and screw.
- Página 10 STEP 1 Attach the Wall Plate to the Wall - Drywall Option IMPORTANT: For stacking configurations, stack from the top down. Remove the front (F) and top (T) covers from the wall plate Level the wall plate and mark the hole locations. CAUTION: Avoid potential injuries or property damage! ●...
- Página 11 STEP 1 Insert anchors CAUTION: Be sure the anchors are seated flush with the surface. Tighten the screws only until they are pulled firmly against the wall plate CAUTION: Improper use could reduce the holding power of the screw. DO NOT over-tighten the screws.
- Página 12 STEP 2 Attach Glass to Wall Plate Slide the glass shelf into the wall plate . Line up the holes in the shelf to the holes in the wall plate as shown. Secure the glass shelf to the wall plate using screws Attach the safety plate to the glass shelf...
- Página 14 STEP 3 Manage Cables Single shelf configuration Stacked configurations For stacked configurations, cables can be routed through the Cables can be routed through the opening in the lower back of inside of the wall plates . When you are done routing cables the wall plate replace the top (T) and front (F) covers.
-
Página 16: Antes De Comenzar
ESPAÑOL INSTRUCCIONES DE SEGURIDAD IMPORTANTES. CONSÉRVELAS. LEA TODO EL MANUAL ANTES DE UTILIZAR ESTE PRODUCTO. Antes de comenzar Cerciórese de: que los accesorios que planifi ca usar no excedan el límite de peso especifi cado; que la pared escogida para el montaje de su repisa sea una pared de montantes de madera, yeso, hormigón sólido o bloques de cemento; haber leído y comprendido estas instrucciones;... -
Página 17: Piezas Y Elementos De Sujeción Suministrados
ESPAÑOL Piezas y elementos de sujeción suministrados ADVERTENCIA: Este producto contiene piezas pequeñas que, si fuesen tragadas, podrían producir asfixia. Antes de iniciar el ensamblaje, compruebe que todas las piezas estén incluidas y en buenas condiciones. Si faltan piezas o alguna está dañada, no devuelva el artículo al distribuidor;... - Página 18 ESPAÑOL Fijar la placa mural a la pared - Opción para hormigón sólido o bloques de cemento IMPORTANTE: Para las confi guraciones apiladas, comience a apilar de arriba a abajo. Retire las cubiertas frontal (F) y superior (T) de la placa mural Nivele la placa mural y marque la ubicación de los orifi...
-
Página 19: Organización De Cables
ESPAÑOL Realice los orifi cios guía. IMPORTANTE: Los orifi cios guía DEBEN realizarse con una mecha de 10 mm (3/8 pulgada) de diámetro hasta una profundidad de 38 mm (1½ pulgadas). Inserte los anclajes PRECAUCIÓN: Cerciórese de que los anclajes hayan quedado nivelados respecto de la superfi cie. Ajuste los tornillos solamente hasta que queden fi... - Página 20 Thank you for choosing Sanus VuePoint! Please take a moment to let us know how we did: Call us: 1-888-333-9952 Email us: info@sanus.com Leave a review: vuepoint.sanus.com UK: 0800 056 2853 Find us on Facebook: SANUS Follow us on Twitter @sanussystems Milestone AV Technologies and its affi liated corporations and subsidiaries (collectively, “Milestone”), intend to make this manual accurate and complete.