Installation Location; Installing The Indoor Unit - Mitsubishi Electric Mr.SLIM PLA-A12EA7 Manual De Instalación

2. Installation location

Refer to the outdoor unit installation manual.
3. Installing the indoor unit
1
3
5
7
Fig. 3-1
37-3/8 D
3/4 to 1-3/4
33-7/8 to 35-13/16 C
31-1/4 B
5-11/16
7-9/16
8-11/16
33-1/16 A
G
F
E
Fig. 3-2
F
D
2-3/8 10-11/16 14-1/16
E
C
A12, A18
A24, A30, A36, A42
Fig. 3-3
2
4
6
3/4 to 1-3/4
5-11/16
E
F
Min. 59 H
Floor
A
B
(mm, inch)
Models C D
76, 3" 76.5, 3-1/82"
79.5, 3-1/8" 79.5, 3-1/8"
3.1. Check the indoor unit accessories (Fig. 3-1)
The indoor unit should be supplied with the following accessories.
Accessory name
Installation template (top of the package)
1
Washers (with insulation)
2
Washers (without insulation)
Pipe cover (for refrigerant piping joint)
Small diameter
3
Large diameter
Band (large)
4
Band (small)
5
Drain socket
6
Insulation
7
3.2. Ceiling openings and suspension bolt installation
(inch)
locations (Fig. 3-2)
Caution:
Install the indoor unit at least 2.4 m, 94-1/2 inch above floor or grade level.
For appliances not accessible to the general public.
• Using the installation template (top of the package) and the gauge (supplied as an
accessory with the grille), make an opening in the ceiling so that the main unit can
be installed as shown in the diagram. (The method for using the template and the
gauge is shown.)
* Before using, check the dimensions of template and gauge, because they
change due to fluctuations of temperature and humidity.
* The dimensions of ceiling opening can be regulated within the range shown in
Fig. 3-2; so center the main unit against the opening of ceiling, ensuring that the
respective opposite sides on all sides of the clearance between them becomes
identical.
• Use M10 (3/8") suspension bolts.
* Suspension bolts are to be procured at the field.
• Install securely, ensuring that there is no clearance between the ceiling panel &
grille, and between the main unit & grille.
A Outer side of main unit
B Bolt pitch
C Ceiling opening
D Outer side of Grille
* Note that the space between ceiling panel of the unit and ceiling slab, etc. must be
7 mm, 5/16 inch or more.
*
When the optional multi-functional casement is installed, add 135 mm, 5-5/16 inch
to the dimensions marked on the figure.
Models
A12, A18
A24, A30, A36, A42
(inch)
3.3. Refrigerant and drainage piping locations of
indoor unit (Fig. 3-3)
The figure marked with * in the drawing represent the dimensions of the main unit
excluding those of the optional multi function casement.
A Drain pipe
B Ceiling
C Grille
D Refrigerant pipe (liquid)
E Refrigerant pipe (gas)
F Main unit
* When the optional multi-functional casement is installed, add 135 mm, 5-5/16 inch
to the dimensions marked on the figure.
Q'ty
1
4
4
1
1
6
2
1
1
E Grille
F Ceiling
G Multi functional casement (option)
H Entire periphery
(mm, inch)
A B
241, 9-1/2" 258, 10-3/16"
281, 11-1/16" 298, 11-3/4"
3