Paper - Sony UP-895 Instrucciones De Uso

8 OUTPUT switch
Selects the video signal output from the VIDEO OUT
connector on the rear panel.
THRU (SW-DOWN): Signals are output directly to the
video monitor.
EE (SW-UP): Signals are output to the video monitor
after being processed by the printer.
In this mode, the impedance at the VIDEO IN connector
is 75 ohms regardless of the setting of the 75Ω ON/OFF
switch qs.
9 AGC (Automatic Gain Control) switch
Adjusts the input signal to the optimum printing level.
OFF (SW-DOWN): Normally keep this switch set to
this position.
ON (SW-UP): When the printout image appears too
dark or too light, set the switch to this position to adjust
the input signal to the optimum level.
0 RESERVED switch
Keep this switch set to the factory setting (SW-DOWN)
qa INPUT switch
B & W (SW-DOWN): When the signal to be printed is
black and white, set the switch to this position.
COLOR (SW-UP): When the signal is color, set the
switch to this position.
qs 75Ω ON/OFF switch
ON (SW-DOWN): When nothing is connected to the
VIDEO OUT connector, set the switch to this position.
OFF (SW-UP): When a video monitor or other video
equipment is connected to the VIDEO OUT connector,
set the switch to this position.
When the OUTPUT switch 8 is set to EE (SW-UP), the
impedance at the VIDEO IN connector is fixed to 75
ohms.
Example:
When you connect two printers to one piece of video
equipment, set the 75Ω switch of one of the printers to
ON, and the other to OFF.
When you connect the printer and a video monitor to the
video equipment, set the 75Ω switch to OFF.

Paper

Use only UPP-110S/110HD/110HG paper as
specified for the UP-895/895MD/895CE. If another
type of paper is used, the quality of the printout
cannot be guaranteed. Use of another type of paper
may also cause malfunction of the printer.
You cannot use the UPP-110HA paper as specified
for the UP-880/890MD/890CE.
Type of paper
The following types of paper are available.
Printing quality
TYPE I (Normal)
TYPE II (High Density)
TYPE V (High Glossy)
Notes on paper
Storing unused paper
Avoid storing unused paper in a location subject to the
following. Storage of unused paper in such a place
results in deterioration of unused paper.
• Store unused paper in a cool and dark place (below
30°C or 86°F).
• Do not store unused paper in a hot or humid place. Do
not leave unused paper in direct sunlight or other
bright places.
• Do not allow any volatile organic solvent or vinyl
chloride to touch unused paper. Alcohol, plastic tape
or film will deteriorate unused paper.
When loading paper
• Do not fold the paper or touch the printing surface.
Dust or finger prints are likely to cause poor print
quality.
• Before loading the paper roll, remove the label
attached to the top of paper roll and pull out the first
15 to 20 cm (6 to 8 inches). The label mark is likely to
cause poor print quality.
Storing printouts
• Avoid storing printouts in a location subject to the
following. Storage of your printouts in such a place
results in fading of printouts.
– Store printouts in a cool and dark place (below
30°C or 86°F). We recommend storing printouts in
a bag made of clay-free paper or polypropylene.
– Do not store printouts in a hot or humid place. Do
not leave printouts in direct sunlight or other bright
places.
– Do not allow any volatile organic solvent or vinyl
chloride to touch printouts. Alcohol, plastic tape or
film will cause the printout to fade.
• Do not stack your printouts on or under a diazo copy
sheet. Also do not attach the printed surface to another
printed surface. The printout may become discolored.
• To attach the printout to another piece of paper, use
double-sided adhesive tape or water-based glue.
Setting Up the Printer/Paper
Type of paper
UPP-110S
UPP-110HD
UPP-110HG
Preparation
25