OttLite D59PNC Guia De Inicio Rapido

C
ON/OFF DIMMABLE
MARCHE; ARRÊT INTENSITÉ RÉGLABLE
ENCENDIDO/APAGADO BRILLO REGULABLE
Soft Touch Flex LED Lamp
D59PNC D5900C D5980C D5900B D59PNB
D5900B-FFP D59PNB-FFP
INS150174
H
G
D
B
F
E
A
D59CPC
PL-0058T
English
CONGRATULATIONS!
You've purchased the finest in natural lighting technology with
your new OttLite ® product.
PRODUCT REGISTRATION FORM
Please complete the enclosed Product Registration Form and
return it today by mail, or register online by going to:
www.warranty.ottlite.com
NOTE: THIS UNIT IS FULLY ASSEMBLED
1. Remove lamp from packing placing lamp body base (A) flat on
a steady surface.
2. Connect the AC Adapter input (E) into connector (F) in the
rear-bottom of the lamp.
3. Plug the A/C adapter (D) into a standard household 120V AC
outlet. Note: Only use with the supplied AC adapter to
avoid damage or fire.
4. Turn the lamp ON & OFF by using power switch (B) located in
the top of base (A). Power switch (B) is a "touch" switch that
controls the dimmer function of the lamp.
5. To power LED lighting, slightly touch the switch (B) to achieve
the following:
• to turn lamp "ON"; touch the switch "once"
• to turn lamp "OFF"; touch the switch a "second" time.
6. To power LED dimmer setting, slightly touch the switch (B) to
turn "ON" lamp and achieve the following:
• to operate dimmer function; continuously "press" switch until
light reaches its lowest setting or "stop" pressing switch
when reaching desired lower light level.
• after reaching desired lower light level, continuously "press"
switch again until reaching original setting.
NOTE: If dimmer function was employed prior to turning "OFF"
lamp, the lamp will return to light setting last employed unless
disconnected from adaptor.
7. To position the shade simply bend the flex-neck (G) as needed
to point the light. Hold lamp base (A) while adjusting the lamp.
SAFETY WARNING:
TO REDUCE THE RISK OF
FIRE, ELECTRIC SHOCK, OR INJURY TO PERSONS
1. Turn lamp off and WAIT UNTIL LAMP HEAD (C) and
ADAPTER (D) ARE COOL before handling.
2. The lamp head (C) might get hot after several hours of
continuous use, DO NOT place your hands directly on or block
vent (H) located on top of the lamp head.
3. Never use with an extension cord unless the plug can be fully
inserted into the receptacles in the extension cord.
4. Do not alter the plug.
5. The lamp head included with this unit cannot be replaced by
the consumer.
NOTE: The important safety instructions appearing in this
instruction sheet are not meant to cover all possible conditions
and situations that may occur. It must be understood that
common sense, caution, and care must be used with any
electrical product.
Soft Touch Flex LED Lamp
CAUTION!
IF THE ExTERNaL FLExIbLE CabLE OR CORD OF
THIS LUmINaIRE IS DamagED, IT SHaLL bE ExCLUSIvELY REPLaCED bY
THE maNUFaCTURER OR ITS SERvICE agENT OR a SImILaR qUaLIFIED
PERSON IN ORDER TO avOID a HazaRD. INDOOR USE ONLY.
FCC PART 15
Note: This equipment has been tested and found to comply with the
limits for a Class B digital device, pursuant to Part 15 of the FCC
rules. These limits are designed to provide reasonable protection
against harmful interference in a residential installation. This
equipment generates, uses and can radiate radio frequency energy
and, if not installed and used in accordance with the instructions,
may cause harmful interference to radio communications.
However, there is no guarantee that the interference will not occur
in a particular installation. If this equipment does cause harmful
interference to radio or television reception, which can be determined
by turning the equipment off and on, the user is encouraged to try to
correct the interference by one or more of the following measures:
» Reorient or relocate the receiving antenna.
» Increase the separation between the equipment and receiver.
» Connect the equipment into an outlet on a circuit different from
that of the receiver.
» Consult the dealer or an experienced radio/TV technician
for help.
ICES-3 ( B ) /NMB-3 ( B )
CAUTION:
Any change or modification to product
not expressly recognized by OttLite Technologies voids OttLite's
responsibility for proper function of product.
AC/DC ADAPTER
Input: AC 100-240V, 50/60 Hz, 0.2A
Output: 13V DC, 0.23A with a Male DC Plug
REV061915