OttLite DMKCH9 Guia De Inicio Rapido

D
C
A
K
E
F
G
Diagram 3
Extended Reach LED Desk Lamp
DMKCH9
INS140154
B
Diagram 1 Diagram 2
L
Diagram 4
Diagram 5
English
CONGRATULATIONS!
You've purchased the finest in natural lighting technology with
your new OttLite ® product.
PRODUCT REGISTRATION FORM
Please complete the enclosed Product Registration Form and
return it today by mail, or register online by going to:
www.warranty.ottlite.com
H
NOTE: THIS UNIT IS FULLY ASSEMBLED
1. Remove lamp from packing placing lamp body base (A) flat on
a steady surface.
2. Connect lamp input (F) into power adapter connection (G).
3. Plug the A/C adapter (E) into a standard household 120V AC
outlet. Note: Only use with the supplied AC adapter to
avoid damage or fire.
4. Turn the lamp ON & OFF using power switch in touch panel (B)
located on lower lamp body.
5. Touch panel (B) includes "touch" keys that control the lamp's
brightness. This lamp provides seven levels of brightness. See
Touch key Instructions section for operating instructions.
6. To reposition the light, hold base (A) steady and grasp either
J
lamp body (C) or shade (D) depending on needed adjustment.
NOTE: CAUTION when moving shade (D) as shade vent (K)
will release heat in the "ON" position.
7. To facilitate movement of lamp body (C) and shade (D), release or
tighten knobs (H, J) as needed. Use tool accessory (L) to tighten
knobs (H, J). DO NOT OVER TIGHTEN or lamp may be damaged.
See diagram 2.
8. Refer to Diagrams 1 through 4 for lamp maximum adjustment
range. NOTE: When lamp is fully extended forward, avoid
rotating lamp body beyond 45° left or right; see diagram 4.
CAUTION: DO NOT FORCE the shade or lamp body rotation
outside allowable adjustable range as excessive adjustment
may cause damage.
Touch Key Panel Instructions
1. To power lamp and operate LED brightness settings, slightingly
touch required "key" to achieve the following:
• Turn lamp "ON/OFF": touch power button for "ON/OFF"
mode as needed.
• To adjust brightness: to engage individual level of
brightness, touch each level of brightness from left to right
(lower settings on LEFT; higher settings on Right) on touch
panel (B). NOTE: level of brightness can also be
reached by one fluid touch motion from left to right or
right to left. See diagram 5.
SAFETY WARNING:
FIRE, ELECTRIC SHOCK, OR INJURY TO PERSONS
1. Turn lamp off and WAIT UNTIL LAMP SHADE (D) is COOL
before handling.
MT-L82
Extended Reach LED Desk Lamp
2. The LED panel located in shade (D) might get hot after several
hours of continuous use, DO NOT place your hands directly on
LED light panel or vent on shade surface.
3. Never use with an extension cord unless the plug can be fully
inserted into the receptacles in the extension cord.
4. Do not alter the plug.
5. The lamp head included with this unit cannot be replaced by
the consumer.
NOTE: The important safety instructions appearing in this
instruction sheet are not meant to cover all possible conditions
and situations that may occur. It must be understood that
common sense, caution, and care must be used with any
electrical product.
CAUTION!
THIS LUmINaIRE IS DamagED, IT SHaLL bE ExCLUSIvELY REPLaCED bY
THE maNUFaCTURER OR ITS SERvICE agENT OR a SImILaR qUaLIFIED
PERSON IN ORDER TO avOID a HazaRD. INDOOR USE ONLY.
FCC PART 15
Note: This equipment has been tested and found to comply with the
limits for a Class B digital device, pursuant to Part 15 of the FCC
rules. These limits are designed to provide reasonable protection
against harmful interference in a residential installation. This
equipment generates, uses and can radiate radio frequency energy
and, if not installed and used in accordance with the instructions,
may cause harmful interference to radio communications.
However, there is no guarantee that the interference will not occur
in a particular installation. If this equipment does cause harmful
interference to radio or television reception, which can be determined
by turning the equipment off and on, the user is encouraged to try to
correct the interference by one or more of the following measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from
that of the receiver.
• Consult the dealer or an experienced radio/TV technician
for help.
CAUTION:
not expressly recognized by OttLite Technologies voids OttLite's
responsibility for proper function of product.
This Class B digital apparatus complies with Canadian ICES-003
TO REDUCE THE RISK OF
Power Adapter specification
Input: AC 100-240V, 50/60 Hz, 0.35A (max)
Output: 12V DC, 1000mA with a Female DC Plug
IF THE ExTERNaL FLExIbLE CabLE OR CORD OF
Any change or modification to product
REV120314