Revell Control Prion Manual De Instrucciones página 8

Your helicopter has already been connected to the remote control in the factory. Should you have to reconnect the remote please proceed as follows:
1. Switch off helicopter and remote control.
2. Push and hold the right-hand trim button.
3. Switch the remote control on whilst the right trim button is pushed down.
4. The red LED on the remote control is flashing.
4. geNerAL FLigHt tiPS:
• Always lay the helicopter down on a smooth surface. A slanting surface may negatively affect
the starting characteristics of the helicopter.
• Always move the regulator slowly and sensitively.
• Always observe the helicopter and not the remote control unit!
• Move the actuating regulator downwards slightly as soon as the helicopter lifts off from the
ground. In order to maintain the flying height, adapt the actuating regulator settings.
• If the helicopter goes lower, move the actuating regulator upwards slightly.
• If the helicopter rises, move the actuating regulator downwards slightly.
• In order to fly into a curve, it is often sufficient to tap the direction regulator gently into the
appropriate direction. During the first flight attempts, people tend to control the helicopter too
vehemently. The control regulator should always be moved slowly and carefully - never quickly
or suddenly.
• Beginners should, after trimming, first try to command the actuating regulator correctly. The
helicopter does not necessarily have to fly straight ahead at first - it is more important to main-
tain a consistent height of approximately one metre above the floor by repeated, brief tapping
of the actuating regulator. Only then should you practice moving the helicopter left and right.
After a crash, always move the slide control completely downwards.
If the helicopter rotor blades are damaged and you have to replace them, proceed as follows:
Ensure that you do not mix
up the rotor blades before
assembly.
Problem:
the rotor blades do not move.
Problem:
the helicopter stops for no clear
reason during flight and drops.
Problem:
the helicopter cannot be
controlled.
Problem:
the helicopter only pivots on its
own axis to the left or right.
You can find further tips and tricks on the Internet at www.revell-control.de.
At www.revell-control.de, you can find our possibilities to order,
replacement tips for spare parts, and further useful information
on all revell control models.
8
Connection of the helicopter to the remote control
guidelines on safe flying
tips for operation
replacing the rotor blades
1. Take a Phillips screwdriver and
carefully unscrew the screws on
the rotor blade.
Safety tips
resolution of errors
Cause:
• The ON/OFF switch is set to "OFF".
• The battery power is too low or drained.
Cause:
• The battery power is too low.
Cause:
• Another infrared source is disturbing the
signal transmission.
• The signal transmission is disturbed due to
bright light irradiation.
Cause:
• Connection between helicopter and remote
control has disconnected.
Service guidelines
5. Now switch on the helicopter, the LED underneath the helicopter is flashing.
6. As soon as the red LED on the remote control flashes continuously, the connection
is completed and you can start.
5. SuitABLe FLigHt eNviroNMeNt:
The location in which the helicopter is flown must fulfil the following criteria:
1. It should be a closed room in which there are no strong draughts. If possible,
no air conditioning, heating fans etc. should be present which may generate air streams.
2. The room should be at least 10 m long, 6 m wide and 3 m high.
3. There should be no objects in the room (fans, lamps etc.) which might hinder flight.
4. On starting, you must ensure that all living creatures - including the pilot - are standing
at least 1-2 m away from the helicopter when the flight begins.
5. Always observe the helicopter to ensure it does not fly at the pilot, other people or animals
and injure them.
cAutioN!
Since 2005, there is an obligation of insurance for model aircraft and helicopters flown out-
doors. Please consult your private liability insurance and make sure that your new and present
models are included in this insurance. Please obtain this confirmation in writing and store
it at a safe place. Alternatively, DMFV offers in the Internet on www.dmfv.aero a free trial
membership incl. insurance.
2. Now carefully pull the rotor
blade off the holder.
remedy:
remedy:
remedy:
remedy:
3. Insert the new rotor blade carefully into the
holder and tighten the screw.
Caution: Do not screw in the screw too tightly.
The rotor blade must have some play.
• Turn the ON/OFF switch to "ON".
• Charge up the battery (power pack).
• Charge up the battery.
• Avoid possible infrared disturbance sources
or switch them off.
• Use the helicopter in a different location.
• Reconnect helicopter and remote control
(see above)
www.revell-control.de