Publicidad
Idiomas disponibles
Idiomas disponibles
PROGRAMMS ASSIGNATION
Any of the 8 programmes (from P0 to P7) can be assigned to any of the days of the
week; for doing that, enter to "MENU PROGRAM" by pressing MENU, press "OK" and
display shows "PROG ASSIGN", enter with "OK" and then you can see ASSIGN and
segment ( ) close to day 1; using keys ( Δ ) and ( ∇ ) assign the desired programme
from P0 to P7, then validate with "OK"; then the segment ( ) moves to next day of the
week. Repeat the above mentioned process for all the days of the week.
MANUAL MODE. OFF MODE
From normal mode, if you press key (
and will not consider the programmed chronogram, only the set temperature. To select
the set temperature, just use keys ( Δ ) and ( ∇ ) and validate it with "OK".
If we want to deactivate the NEO, from normal mode press twice the key (
displays shows SET OFF. In this mode the NEO shows the room temperature but
does not execute any action except maintenance and security programmes if
activated. To come back to normal mode, press (
EXTRA FUNCTIONS
By pressing keys Menu, ( Δ ), ( ∇ ) and "OK" we enter in the EXTRAS menu.
WINTER / SUMMER TIME CHANGE
In menu "EXTRAS SEASON" it can be selected: Auto, manual or deactivated.
In Auto mode, the official time is automatically changed during last Sunday in March
and last Sunday in October. Validate it with "OK".
In Manual mode, date and hour of the change of the official time can be programmed,
both Winter to Summer and Summer to Winter. Validate always with "OK".
In deactivated mode, there is no change of hour.
HEATING – AIR CONDITION
To select working mode of NEO for heating or air condition, enter MENU EXTRAS ,
EXTRAS HEAT-AC, validate with "OK" and by using ( Δ ) and ( ∇ ) select HEATING
for heating mode (display shows (
(display shows (
) when load is active).
EXTRA PROGRAMMS
Three types of extra programs can be selected: Interrupt (Holidays), Maintenance and
Security
HOLIDAYS: It allows to maintain the NEO in OFF state during a certain number of
days and hours, after which the NEO comes back to the normal mode. Display shows
HOLIDAYS and the symbol (
) during the programmed time (maximum 99 days and
23 hours). To cancel this program, enter HOLIDAYS and program 00 to day and hour
or change the working mode (Automatic, Manual, OFF). SECURITY (PROTECT). This
program avoid freezing of installation. If it is active, NEO will switch on the heater if the
temperature is under 6 ºC, also in OFF state or HOLIDAYS program. Displays shows
(
) symbol. This program can only be used in heating mode.
MAINTENANCE. This programme avoid the installation to be inactive during long
periods of time. If during the last week there has not been any load activation, this
program activates the load during two minutes on Wednesday at 12:00 hours. During
this period of time, display shows "CLEANING". If this program is activated, this
programme will also work even in OFF state or in HOLIDAY programme.
REGULATION (TEMPREG)
There are two modes of temperature regulation: ON-OFF and P.I. control.
ON-OFF: When selecting this option, NEO works as a normal thermostat and when
the measured temperature is equal to the set temperature plus the programmed
differential, the load switch off, and it switch on when the measured temperature goes
under the set temperature. The differential values are selected with (Δ) and (∇ ) after
validating with "OK" the option ON-OFF. The differential interval can be selected from
0,2 ºC to 1,0 ºC.
CONTROL P.I. (CRTL-PI). When selecting this option, the working mode is
conditioned to an established time base according with the following:
T measured ≥ T programmed +0,6º C
T measured = T programmed +0,5º C
T measured = T programmed +0,4º C
T measured = T programmed +0,3º C
T measured = T programmed +0,2º C
T measured = T programmed +0,1º C
T measured = T programmed
T measured = T programmed - 0,1º C
T measured = T programmed - 0,2º C
T measured = T programmed - 0,3º C
T measured ≤ T programmed - 0,4º C
This mode of regulation gives more stability to the set temperature.
PROBES
Menu PROBES is used to correct the temperature measured by the probe and to
include an external probe.
If a difference between the measured temperature and real temperature is noted, then
there is the possibility to adjust the values by using option "CORRECTION".
CORRECTION. Select PROBES, then CORR INT and the displays shows "OFFSET
INTERNAL". Select the value by using ( Δ ) and ( ∇ ). Validates with "OK".
To include an external probe, after connecting it in the appropriate terminals, select
MENU PROBES, EXTERNAL PROBE, validate with "OK", select "yes" and validates
again with "OK".
Never select option "yes" if there is no external probe, as display could show wrong
measurements. The probe (internal or external) that controls the working mode of
NEO can be selected by entering in MENU PROBES, CONTROL, validating with
"OK"; keys (Δ) and (∇) select INTERNAL or EXTERNAL and validate with "OK". If the
selected probe is external, the temperature can also be corrected if a difference
between the measured temperature and real temperature is noted, in the same way
as explained for the internal probe.
COUNTER
It indicates the number of hours that the load (heating or air condition) has been
working. To access counter, enter MENU EXTRAS, COUNTER and display will show
"COUNTER HEATING" and the number of working hours; pressing ( Δ ) display shows
"COUNTER AIR CON" and the working hours. By pressing again ( Δ ) we can reset
the counter of heating hours as display shows "DELETE HEATING"; If we press "OK"
then the counter goes to zero, and if we press again ( Δ ) the same operation can be
repeated with the air condition hours counter.
) the NEO will work as a normal thermostat,
).
)when load is active) or AIR CON for air condition
load OFF
1 minute
ON; 9 minutes OFF
2 minutes ON; 8 minutes OFF
3 minutes ON; 7 minutes OFF
4 minutes ON; 6 minutes OFF
5 minutes ON; 5 minutes OFF
6 minutes ON; 4 minutes OFF
7 minutes ON; 3 minutes OFF
8 minutes ON; 2 minutes OFF
9 minutes ON; 1 minute OFF
relé ON
RESET
If we want to re-start the NEO, maintain pressed the key "OK" and then press at the
same time the keys (
and the programme ask for the language.
LOCKING THE KEYPAD
To prevent accidental or non desired usage of the chronothermostat it is possible to
lock the keypad. To activate the lock: maintain pressed the key "OK" and then press at
the same time the keys (
process. If the keypad is locked, the display shows "KEY BLOQ"
PHONE CONTROL
Terminals 4 and 5 of NEO can be used to connect a phone control. When the phone
control closes the circuit, NEO goes to OFF mode (in this case, display shows
) and
PHONE-OFF) and returns to the previous mode when the phone control opens the
circuit.
TECHNICAL FEATURES
Power supply:
Switching capacity
Contact type and material:
Battery duration:
Action type:
Number of programmes:
Minimum programmable time:
Temperature accuracy:
Resolution:
Operating accuracy:
Temperature measurement period
Output relay updating
Time reserve for battery replacement:
Operating temperature:
Measurement and regulation
with internal probe:
Measurement and regulation
with external probe:
Protection class:
Protection type:
Pollution situation:
DIMENSIONS
11.5
) and (
). The defective parameters are then loaded to NEO
) and (
). To unlock the keyboard, repeat the same
2 alkaline batteries LR03(AAA) 1,5 V
5 (1) A /250 V∼
Changeover AgNi 90/10
1 year roughly
1B, 1S, 1T y 1U
8
30 minutes
± 0,5 ºC
0,1 ºC
≤ ±1,2 s /24 h a 23 ºC
30 s
1 minute
10 minutes
0 ºC to +50 ºC
0 ºC to +50 ºC
–10 ºC to +50 ºC
II according to EN 60335 when
mounting as intended
IP40 according to EN 60529
Normal
122
30
26
17
4
MOUNTING DIMENSIONS
ORBIS TECNOLOGÍA ELÉCTRICA, S.A.
Lérida, 61. E-28020 MADRID
Teléf: +34 1 567 22 77 · +34 1 567 22 90
Fax : +34 1 571 40 06 · +34 1 570 20 00
e-mail: Info @ orbis.es
Internet: www.orbis.es
27
A016.73.52646
Publicidad
