Chain Lubrication; Chain Maintenance - EINHELL GC-PC 1235/1 Manual De Instrucciones

Ocultar thumbs Ver también para GC-PC 1235/1:

Manual de instrucciones original (96 páginas)

Tabla de contenido

Idiomas disponibles

necessary, use a long screwdriver to move the

ﬁ lter to its correct position, taking care not to

damage in the process.

7. Fill tank with fresh fuel / oil mixture. See Sec-

tion Fuel and Lubrication. Install fuel cap.

7.2.3 Spark plug (Fig. 15A-15C)

Note: To ensure that the saw's engine retains its

power, the spark plug must be clean and have the

correct electrode gap (0.6 mm). The spark plug

must be cleaned or replaced after every 20 hours

of service.

1. Set the On/Oﬀ switch to Stop (0)".

2. Remove the top cover (14) by undoing the co-

ver fastening screw (A) on the cover. You can

then remove the cover (Fig. 15A).

3. Lift out the air ﬁ lter (15) (Fig. 15B).

4. Disconnect the ignition cable (C) from the

spark plug by pulling and twisting it simultane-

ously (Fig. 15C).

5. Remove the spark plug using a spark plug

wrench.

6. Clean the spark plug with a copper wire brush

or ﬁ t a new one.

7.2.4 Carburetor setting

The carburetor has been set to its perfect adjust-

ment at the factory. If it requires adjusting, take the

saw to your nearest authorized after-sales service

outlet.

7.2.5 Chain bar

•

Grease the guide rail starwheel after every 10

hours of operation. This is necessary to get

the best performance from your chainsaw.

(Fig. 16) Clean the lube hole, then place the

lube gun (not included) at the hole and pump

grease into the bearing until grease is forced

out.

•

Clean the groove which the chain runs in as

well as the oil entry hole on a regular basis

using a commercially available cleaning tool.

(Fig. 17A) This is important to ensure optimal

lubrication of the guide rail and chain during

operation.

•

Remove burrs and sharp edges on the guide

rail (2) by carefully filing them down with a flat

file. (Fig. 17B)

•

Turn the guide rail (2) around after every 8

hours of operation so that it wears evenly on

the top and bottom.

Oil passages

Oil passages on the bar should be cleaned to en-

sure proper lubrication of the bar and chain during

operation.

Anl_SA_GC_PC_1235_1_SPK8.indb 34

Note: The condition of the oil passages can be

easily checked. If the passages are clear, the

chain will automatically give oﬀ a spray of oil

within seconds of starting the saw. Your saw is

equipped with an automatic oiler system.

Automatic chain lubrication.

The chain saw is equipped with an automatic oil

lubrication system with a toothed wheel drive. It

automatically supplies the bar and the chain with

the right quantity of oil. The moment the engine is

accelerated, the oil also starts to ﬂ ow through the

bar plate more quickly as well.

The chain lubrication system has been set to its

perfect adjustment at the factory. If it requires

adjusting, take the saw to your nearest authorized

after-sales service outlet.

On the underside of the chainsaw you will ﬁ nd the

setting screw (A) for the chain lubrication system

(Fig. 21). Turning the screw counter-clockwise in-

creases the chain lubrication, turning it clockwise

decreases the chain lubrication.

To check the chain lubrication, hold the chain saw,

with the chain, over a piece of paper and run it at

full speed for a few seconds. You will be able to

judge the set amount of oil from the paper.

On a regular basis, check that the chain lubrica-

tion is working correctly. Test chain lubrication

before the ﬁ rst cut, after several cuts and always

after any maintenance.