Plugr PL415 Guia De Inicio Rapido página 7

1
PL1003 4
2
PL1015 15
3
PL1018 1
4
PL1019 1
5
PL1022 1
6
PL1024 1
7
PL1029 4
8
PL1031 1
9
PL1042 2
10
PL1044 12
11
PL1045 4
12
PL1052 4
13
PL1056 8
14
PL1057 4
15
PL1072 11
16
PL1077 1
17
PL1089 1
18
PL1091 6
19
PL1097 1
20
PL1115 9
21
PL1123 1
22
PL1126 1
23
PL1129 1
24
PL1135 2
25
PL1138 1
26
PL1142 8
27
PL1143 4
28
PL1157 1
29
PL1158 2
30
PL1168 1
31
PL1175 4
32
PL1176 4
33
PL1177 8
MANUALS FOR OLDER UNITS CAN BE FOUND AT WWW.SOURCEONEOPE.COM
Parts List for Model PL415
Rubber Latch Kit
Flat Washer, Ø5/16
Engine Pulley, Ø3.5
Cogged V-Belt, B 35"
Idler Pulley, Ø2.75
Hex Bolt, 1/2-13 UNC x 2.0"
Nylock Nut, 1/4-20 UNC
Cotter Pin, Ø1/16 x 3/4"
Cartridge Bearing, Ø1.0
Flat Washer, Ø3/8
Nylock Nut, 3/8-16 UNC
Grease Fitting, 1/4-28
Jam Nut, 5/8-11 UNC
Tine, Ø5/8
Nylock Nut, 5/16-18 UNC
Clevis Pin, Ø1/4 x 3/4"
Retractor Plate Cable
Flat Washer, Ø1/4
400 Series Retractor Plate
Stainless Rivet, Ø1/8 x 1/4
Key, 3/16" x 1-1/2"
Safety Switch Wire
Safety Switch
Handle Lock Sleeve
Clutch Torsion Spring
Hex Bolt, 3/8-16 UNC x 2"
Hex Bolt, 5/16-18 UNC x 1-1/2"
Extension Spring, Ø3/4 x 1"-3"
Shoulder Bolt, Ø5/16 x 1/4"
Clutch Cable, 37"
Tine Rod
Tine Rod Cap
Journal Bearing, Ø2.0
THESE INSTRUCTIONS ARE TO BE USED ONLY FOR:
MODEL PL415 SERIAL #1001
34
PL1178 4
35
PL1179 10
36
PL1184 1
37
PL1198 1
38
PL1201 1
39
PL1248 4
40
PL1267 4
41
PL1272 2
42
PL1288 1
43
PL1291 2
44
PL1296 1
45
PL1329 3
46
PL1512 2
47
PL1523 1
Half-Hex Shank Low-profile Head, Open
48
PL1534 4
49
PL1544 2
50
PL1609 1
51
PL1632 2
52
PL1667 4
53
PL1668 4
54
PL1684 1
55
PL1757 4
56
PL1758 2
57
PL1768 4
58
PL1769 1
PL1769-
59
1
09
PL1769-
60
1
10
61
PL1770 1
62
PL1771 1
63
PL1772 1
64
PL1777 1
65
PL1778 1 Ø.250 Quick Release Pin w/ Lanyard,1"
Fender Washer, Ø5/16
Lock Nut, 3/8-16 UNC
Hex Bolt, 5/16-18 UNC x 1"
Retractor Plate Latch
Retractor Handle
Hex Bolt, 5/16-18 UNC x 1-3/4"
Hex Bolt, 1/4-20 UNC x 1"
Eyebolt, Ø1/2 x 1/4-20 UNC
400 Series Clutch Lever
Rivet, Ø3/16 x 3/8"
4 Tine Crank
Flat Washer, Ø1/2
Bushing, 1/2 ID x 3/4 OD x 1/2"
Cotter Pin, Ø1/8 x 1"
End
Hex Bolt, 5/16-18 UNC x 2"
GX120 Honda Engine w/ Gearbox
Retractor Plate Arm
Hex Bolt, 3/8-16 UNC x 1-1/2"
Hex Bolt, 5/8-11 UNC x 4-1/2"
Safety Switch Ground Wire
Washer, USS Ø5/16 Thru-Hard
Shoulder Bolt, Ø1/2 x 5/8"
Wheel, 12" Semi-Pneumatic w
Ø5/8Bearing Hub
400 Series Frame
Upper Belt Tensioner Bracket
Lower Belt Tensioner Bracket
400 Series Cover
400 Series Handle
Clutch Arm
PL415 Decal Kit