Default Button Settings; General Button Programming Warnings; Programming Buttons For Generic Or Coded Actuator - Comelit Smart kit Manual Tecnico

Default button settings

DIP S2
DIP 1 DIP 2 DIP 3 DIP 4 P1
0 0 0 0
CCS
1 0 0 0
ACT
0 1 0 0
INT
1 1 0 0
ACT
0 0 1 0
ACT
1 0 1 0
INT
0 1 1 0
1 1 1 0
INTb
0 0 0 1
CCS
1 0 0 1
0 1 0 1
CCP
1 1 0 1
PAN
0 0 1 1
1 0 1 1
INT
0 1 1 1 NULL
1 1 1 1
A Lock- release
Speech
ACT Actuator
AI Self-ignition
CCP Main switchboard call

General button programming warnings

If the default settings (see table on page 27) do not refl ect requirements,
the buttons can be programmed differently by carrying out the steps below.
At the end, set S2 DIP switches 1-2-3-4 to the combination 1111
(PROG setting in the confi guration tables on pages 27, 28, 29). In this
dip switch setting, the buttons control the programmed functions;

Programming buttons for generic or coded actuator

DIP S2
DIP 1 DIP 2 DIP 3 DIP 4
0 0 0 0
1 0 0 0
0 1 0 0
1 1 0 0
0 0 1 0
1 0 1 0
0 1 1 0
1 1 1 0
0 0 0 1
1 0 0 1
0 1 0 1
1 1 0 1
0 0 1 1
1 0 1 1
0 1 1 1
1 1 1 1
Example:
on a monitor with user code 5, P1 programming = generic actuator, P2 =
coded actuator (code 125)
1. Set S2 DIP switch 5-6 to the combination 01
» LED 1 (red) fl ashes
2. Refer to the table on page 27 and select a combination in which the
actuator function (ACT) is listed for the buttons you wish to program.
E.g.: for P1= generic actuator, set S2 DIP switches 1-2-3-4 to the
A
P2
AI
AI
A
AI
CCS
ACT ACT
ACT
AI D
INT
PAN
A
K CCS
K
CCP
D INTb
INT
NULL NULL NULL
CCS
K
D
PAN
INT
A
P1 P2
ACT
A
ACT
ACT ACT ACT
ACT
A
2
LED1
P3 P4
ACT D
INT INTb
INTb ACT
CCP PAN
ACT ACT
CCS CCP
K CCS
AI INT
D AI
PAN CCP
PAN ACT
CCS K
INT ACT
INT INT
NULL NULL
PROG
Legend
Switchboard call
Guardian door-entry
phone call
Doctor
Panic
Programmable
intercom, general or
selective
- general internal call
as standard for KIT and
Simplebus Top
the NON-programmed buttons control functions referred to on line
0000 (see table on page 27). Restore the user code setting on S1, see
table A on page 26.
with Art. 6333
P3 P4 P5
ACT
ACT
ACT ACT ACT
ACT
ACT
ACT
PROG
combination 1000 or 1100 or 0010 (P1=ACT), set S1 DIP switches to the
combination 11111111, go to point 3
E.g.: for P2= coded actuator (code 125), set S2 DIP switches 1-2-3-4
to the combination 0010 or 1010 (P2=ACT), set S1 with address 125 in
accordance with table A on page 26, go to point 3
3. Press and release the button to be associated with the function
LED 2
»LED 2 (blue) fl ashes 4 times
»confi rmation tone
4. To exit programming mode, set S2 DIP switches 5-6 to the combination
00
» LED 1 (red) switches off
5. When programming is complete, set S2 DIP switches 1-2-3-4 to the
combination 1111. Restore the user code setting on S1, see table A
on page 26.
with Art. 6333
P5 P6
PAN K
D CCS
CCS CCP
K D
ACT ACT
INTb PAN
CCP INTb
PAN D
INT INTb
AI INT
INT AI
ACT D
AI CCS
INT INT
NULL NULL
Two-family intercom
INTb
- for KIT only
NULL No function
Programmed functions,
see pages 27-32
In this Dip switch setting,
the buttons control the
PROG
programmed functions; the
NON-programmed buttons
control functions referred to
on line 0000
P6 P7
ACT ACT
ACT
P7
CCP
PAN
D
AI
ACT
K
INT
ACT
CCP
INTb
CCS
AI
CCP
INT
NULL
DIP S1
ADDRESS
27 27