Publicidad
Idiomas disponibles
Idiomas disponibles
Enlaces rápidos
AUTOMOTIVE PRODUCTS, INC.
MOUNT KIT
SURE-GRIP
OPTIONAL LIGHT
EQUIPO DE MONTAJE
JEU DE MONTAGE
27-1645
MOLDED
SURE-GRIP
STEP BOARDS FOR AVALANCHE WITH CLADDING
STEP
BOARDS
BOARDS
27-6130
27-0010
27-6135
STEP BOARDS AVALANCHE WITHOUT CLADDING
27-0015
27-6530
27-0020, 27-0025, 27-6140, 27-6145, 27-6540
27-0020
27-6140
27-0025
27-6145
27-6540
ITEM
QTY
CONTENTS -
1,2
2
STEP BOARD, PASSENGER (1) AND DRIVER (2) (SOLD SEPARATELY)
3
8
MOUNT BRACKET
4
16
M8-1.25 X 20MM HEX HEAD BOLT
5
12
M8-1.25 HEX NUT
6
16
5/16-18 X .75 SQUARE HEAD BOLT
7
40
5/16" FLAT WASHER
8
16
5/16" LOCK WASHER
9
16
5/16" LOCK NUT
1,2
2
ESTRIBOS, ACOMPAÑANTE (1) CONDUCTOR (2) (SE COMPRA
SEPARADO)
3
8
SOPORTE
4
16
PERNOS CON CABEZA HEXAGONAL M8-1,25 X 20MM
5
12
TUERCAS HEXAGONALES DE M8-1,25
6
16
PERNOS CON CUADRADA DE 5/16-18 X .75
7
40
ARANDELAS PLANAS DE 5/16"
8
16
ARANDELAS DE PRESIÓN DE 5/16"
9
16
TUERCA A PRESIÓN 5/16"
1,2
2
MARCHEPIEDS, PASSAGER (1) ET CONDUCTEUR (2) ACHETÉS
SÉPARÉMENT
3
8
SUPPORT
4
16
BOULONS À TÊTE HEXAGONALE M8-1,25 X 20 MM
5
12
ÉCROUS HEXAGONAUX M8-1,25
6
16
BOULONS À TÊTE CARRÉE 5/16-18 X 0,75 PO
7
40
RONDELLE PLATE 5/16 PO
8
16
RONDELLES A FREIN 5/16 PO
9
16
ÉCROU FREINÉ 5/16 PO.
STEP 1.
Remove contents from box and check for damage. Verify all parts are present. Read instructions completely before beginning. It is
strongly recommended to install the Sure Grip Gap Strip for these vehicle applications.
STEP 2.
Attach mounting brackets as shown.
STEP 3.
Insert square head bolts as shown ( 4 per slot, 8 per board).
NOTE:
For lighted boards, run wiring harness prior to attaching board to brackets (refer to Step 6)
longer wire harness on passenger side.
STEP 4.
For Sure-Grip Running Boards, slide closure strip as shown. Set lights (if purchased) in appropriate location. Attach to Sure-Grip Running
Board as shown.
STEP 5.
Attach board to brackets as shown. Make sure board and brackets are properly aligned and tighten fasteners. Recommended torque
values are 10 FT.LBS. for 5/16" square head fasteners and 23 FT.LBS. for 8mm fasteners.
NOTE:
For lighted version of Molded Step Board, remove plastic cover from each end of under side of board. Proceed to Steps 6-7.
WARNING: INSTALLING LIGHT HARNESS REQUIRES SPLICING INTO VEHICLES ELECTRICAL SYSTEM. WESTIN
RECOMMENDS USING A PROFESSIONAL FOR THIS INSTALLATION. NOTE: AVOID AREAS OF EXCESSIVE HEAT,
VIBRATION, PINCH OR ROTATION WHEN SECURING HARNESS TO VEHICLE. CAUTION: ALWAYS USE A FUSED(+)
HINT:
Molded Step Boards: For longevity, check rubber seals before installation. Rubber grommets around red and blue wires going into
INSTRUCTIONS-INSTRUCCIONES-CONSIGNES
APPLICATION: 2002-08 CHEVY AVALANCHE
APLICACIÓN:
APPLICATION: CHEVY AVALANCHE 2002-08
KIT
27-6000
27-0010, 27-6130, 27-6135, 27-6530
CONTENIDO
- CONTENU
SEE FIGURE 1.
SEE FIGURE 2.
Drill hole through plastic strip and run wires as shown.
POSITIVE SUPPLY SOURCE. UNDERCOAT SEAL FOR HARSH WEATHER.
2005-08 CHEVY SUBURBAN/TAHOE/GMC YUKON, YUKON XL
CHEVY AVALANCHE MOD. 2002-08
,
CHEVY SUBURBAN/TAHOE/GMC YUKON, YUKON XL, MOD. 2005-08
CHEVY SUBURBAN/TAHOE/GMC TYUKON, YUKON XL 2005-08
1
SEE FIGURES 3 AND 4.
WO:
3
TOOLS-
HERRAMIENTA
13MM SOCKET
13MM WRENCH
1/2" SOCKET
RATCHET
TORQUE WRENCH
DADO DE 13MM
LLAVE DE TUERCAS DE 13MM
DADO DE 1/2"
MANERAL
LLAVE DE TORQUE
DOUILLE 13MM
CLÉ 13MM
DOUILLE 1/2 PO
CLIQUET
CLÉ DYNAMOMÉTRIQUE
.
SEE FIGURES 3 AND 4
SEE FIGURE 5.
SEE FIGURE 6.
75-0607 REVISION F 6/30/08
-OUTILS
.
Run
Publicidad
Manuales relacionados para Westin CHEVY Serie
Resumen de contenidos para Westin CHEVY Serie
- Página 1 For lighted version of Molded Step Board, remove plastic cover from each end of under side of board. Proceed to Steps 6-7. WARNING: INSTALLING LIGHT HARNESS REQUIRES SPLICING INTO VEHICLES ELECTRICAL SYSTEM. WESTIN RECOMMENDS USING A PROFESSIONAL FOR THIS INSTALLATION. NOTE: AVOID AREAS OF EXCESSIVE HEAT, VIBRATION, PINCH OR ROTATION WHEN SECURING HARNESS TO VEHICLE.
- Página 2 FINISH PROTECTION Westin products have a high quality finish that must be cared for like any other exposed finish on the vehicle. Protect the finish with a non-abrasive automotive wax, (e.g. Pure Carnauba) on a regular basis. The use of any soap, polish or wax that contains an abrasive is detrimental, as the compounds scratch the finish and open it to corrosion.
- Página 3 PROTECTION DE LA FINITION: Les produits Westin ont une finition de haute qualité qui requiert des soins, comme toute autre finition de véhicule exposée aux éléments. Protéger la finition de façon régulière à l'aide d'une cire non-abrasive (par exemple, Pure Carnauba). L'emploi de tout autre savon, pâte à polir ou cire contenant un abrasif est nuisible, puisque leurs...
- Página 4 ROUGE FIGURE 7 FIGURE 6 FIGURA 7 FIGURA 6 Thank You for choosing Westin products Westin Automotive Products, Inc. For additional installation assistance please call 5200 N. Irwindale Ave. Suite 220 Irwindale, Ca. 91706 Customer service (800) 793-7846 or (507) 375-3559...