Westin 27-1795 Instrucciones

AUTOMOTIVE PRODUCTS, INC.
MOUNT KIT
EQUIPO DE MONTAJE
OPTIONAL LIGHT
JEU DE MONTAGE
27-1795
MOLDED SURE-GRIP
STEP BOARDS
BOARDS 27-6130
27-0010 27-6135
27-0015 27-6530
ITEM QTY CONTENTS - CONTENIDO - CONTENU
1 2 STEP BOARD (PURCHASED SEPARATELY)
2 2 FRONT BRACKET
3 4 CENTER/REAR BRACKET
4 12 5/16-18 X 1.00" HEX HEAD BOLT
5 30 5/16" USS FL AT WASHER
6 12 5/16" LOCK WASHER
7 6 5/16-18 HEX NUT
8 12 5/16-18 X .75" SQUARE HEAD BOLT
9 12 5/16-18 LOCK NUT
10 6 EXTRUDED U-NUT
1 2 ESTRIBOS (SE COMPRAN POR SEPARADO)
2 2 SOPORTE DELANTERAS
3 4 SOPORTE CENTRALES/TRASERAS
4 12 PERNOS CON CABEZA HEXAGONAL DE 5/16-18 X 1,00"
5 30 ARANDELAS PLANAS DE USS 5/16"
6 12 ARANDELAS DE PRESIÓN DE 5/16"
7 6 TUERCAS HEXAGONALES DE 5/16-18
8 12 PERNOS CON CABEZA CUADRADA DE 5/16"
9 12 TUERCA PRESIÓN DE 5/16-18
10 6 TUERCA A PRESIÓN EN "U"
1 2 MARCHEPIED (VENDU SÉPARÉMENT)
2 2 SUPPORTS AVANT
3 4 SUPPORTS CENTRAL/ARRIERE
4 12 BOULONS A TETE HEXAGONALE 5/16-18 X 1,00 PO
5 30 RONDELLES PLATES USS 5/16 PO
6 12 RONDELLES A FREIN 5/16 PO
7 6 ÉCROUS HEXAGONAUX 5/16-18
8 12 BOULON A TETE CARREE 5/16 PO
9 12 ECROU A FREIN 5/16-18
STEP 1. Remove contents from box and check for damage. Verify all parts are present. Read and understand instructions before
beginning.
NOTE: If installing Westin step boards on vehicles equipped with factory step boards, the existing factory hardware can be
used. The mount brackets will be placed over the mounting stud protruding from the rocker panel, and the factory nuts can
be reused. It is strongly recommended to install the Sure Grip Gap Strip for these vehicle applications.
STEP 2. Locate the pair of holes on the bottom of the rocker panel and the square hole next to the round hole on the bottom of the
floor pan. SEE FIGURE 1.
STEP 3. Insert extruded "u" nut through square hole in vehicle floor plan so it is positioned over the round hole. SEE FIGURE 1.
STEP 4. Install brackets to the extruded "u" nuts inserted into the vehicle floor pan with 5/16" fasteners as shown. SEE FIGURE 1.
STEP 5. Install brackets to vehicle rocker panel with 5/16" fasteners as shown. SEE FIGURE 1 for hole locations.
STEP 6. Insert square head bolts as shown (3 per slot, 6 per Step board/Running board). SEE FIGURES 3 AND 4.
boards, run wiring harness prior to attaching board to brackets (refer to Step 7). SEE FIGURES 3 AND 4. Run longer wire harness on
passenger side.
STEP 7. For Sure-Grip Running Boards, slide closure strip as shown. Set lights (if purchased) in appropriate location. Attach to Sure-Grip
Running Board as shown. SEE FIGURE 2. Drill hole through plastic strip and run wires as shown. SEE FIGURE 5.
STEP 8. Attach board to brackets as shown. Make sure board and brackets are properly aligned and tighten fasteners.
Recommended torque values are 10 FT.LBS. for 5/16" square head fasteners and 16 FT.LBS. for 5/16" fasteners. SEE FIGURE 6.
NOTE: For lighted version of Molded Step Board, remove plastic cover from each end of under side of board. Proceed to
Steps 9-10.
WARNING: INSTALLING LIGHT HARNESS REQUIRES SPLICING INTO VEHICLES ELECTRICAL SYSTEM. WESTIN RECOMMENDS USING A
PROFESSIONAL FOR THIS INSTALLATION. NOTE: AVOID AREAS OF EXCESSIVE
INSTRUCTIONS-INSTRUCCIONES-CONSIGNES
APPLICATION: 2007-08 FORD EXPLORER SPORT TRAC
APLICACIÓN: FORD EXPLORER SPORT TRAC 2007-08
APPLICATION:
SURE-GRIP
KIT
27-6000
1
2007-08 FORD EXPLORER SPORT TRAC
WO:
2
TOOLS-HERRAMIENTA -OUTILS
1/2" SOCKET
1/2" WRENCH
RATCHET
RATCHET EXTENSION
TORQUE WRENCH
DADO DE 1/2"
LLAVE DE TUERCAS DE 1/2"
MANERAL
MANERAL EXTENSION
LLAVE DE TORQUE
DOUILLE 1/2 PO
CLEF 1/2 PO
CLIQUET
CLIQUET RALLONGE
CLÉ DE COUPLE
NOTE: For lighted
HEAT, VIBRATION, PINCH OR ROTATION WHEN
75-0799 REVISION B 6/30/08
3
10