Refined Salt And Rinse Aid; Measuring Out The Refined Salt; Measuring Out The Rinse Aid - Whirlpool ADP 422 Manual De Instrucciones

Refined Salt and Rinse Aid

Only use products which have been specifically designed
for dishwashers. Do not use table salt or industrial salt.
(Follow the instructions given on the packaging.)
If you are using a multi-function product, we recommend
that you add salt in any case, especially if the water is hard
or very hard. (Follow the instructions given on the packaging.)
If you do not add salt or rinse aid, the LOW SALT and
LOW RINSE AID indicator lights will remain lit.

Measuring out the refined salt

The use of salt prevents the formation of LIMESCALE on the
dishes and on the machine's functional components.
• It is important that the salt dispenser be never empty.
• It is important to set the water hardness.
The salt dispenser is located in the lower part of the dishwasher
(see Description)
and should be filled:
• When the LOW SALT indicator light in the control panel is lit ;
• See autonomy in the water hardness table.
1. Remove the lower rack and unscrew the container cap
(anticlockwise).
2. Only the first time you do this: fill the
water dispenser up to the edge.
3. Position the funnel
fill the salt container right up to its edge
(approximately 1 kg); it is not unusual for
a little water to leak out.
4. Remove the funnel and wipe any salt
residue away from the opening; rinse the cap under running
water and then screw it on.
It is advisable to perform this procedure every time you add salt
to the container.
Make sure the cap is screwed on tightly, so that no detergent can
get into the container during the wash cycle (this could damage
the water softener beyond repair).
Whenever you need to add salt, we recommend carrying out
the procedure before the washing cycle is started.
Setting the water hardness
For perfect water softener operation, it is essential that the
adjustment be based on the water hardness in your house. Ask
your local water supplier for this information. The factory setting
is for medium water hardness.
• Switch the dishwasher on using the On/Off button.
• Switch it off using the On/Off button
• Hold down the START/PAUSE
you hear a beep.
• Switch it on using the On/Off button
• The display shows the current selection level number and the
salt indicator light.
• Press button P to select the desired hardness level (see
Hardness Table).
• Switch it off using the On/Off button
• Setting is complete!
(°dH = hardness measured in German degrees - °f = hardness
measured in French degrees – mmol/l = millimoles per litre)

Measuring out the rinse aid

Rinse aid makes dish DRYING easier. The rinse aid dispenser
should be filled:
• When the LOW RINSE AID indicator light on the panel/display
• When the dark optical indicator on the dispenser door "E"
(see figure)
and
NEVER pour the rinse aid directly into the tub.
Adjusting the amount of rinse aid
If you are not completely satisfied with the drying results, you
can adjust the quantity of rinse aid used. Turn the adjuster "F".
A maximum of 4 levels can be set according to the dishwasher
model. The factory setting is for a medium level.
• If you see bluish streaks on the dishes, set a low number (1-2).
• If there are drops of water or limescale marks on the dishes,
button for 5 seconds until
Water Hardness Table
level °dH °fH mmol/l
1 0 - 6 0 - 10 0 - 1
2 6 - 11 11 - 20 1.1 - 2
3 12 - 17 21 - 30 2.1 - 3
4 17 - 34 31 - 60 3.1 - 6
5 34 - 50 61 - 90 6.1 - 9
For values between 0°f and 10°f, we do not recommend the use
of salt. A setting of 5 may increase cycle duration.
;
is lit
becomes transparent.
1. Open the dispenser by turning
the cap "G" in an anticlockwise
direction.
2. Pour in the rinse aid, making
sure it does not overflow from the
dispenser. If this happens, clean
the spill immediately with a dry cloth.
3. Screw the cap back on.
set a high number (3-4).
Average autonomy
salt dispenser with 1
wash cycle per day
months
7 months
5 months
3 months
2 months
2/3 weeks
19
EN