Setting The Timer - DeLonghi EX 390 Serie Instrucciones

• In particularly severe environmental conditions (large size
of the environment, high temperature or humidity outside,
poor insulation of the room, too many of people or strong
heat load in the room, strong exposure to the sun ...) this
device may not be able to reach the best comfort level.
ARCTIC WHISPER (available in conditioning mode only)
By activating this function, the operating noise is further
reduced. To activate it, touch on the remote control the
button (D6). The display shows the relative symbol (C12).
SWING FUNCTION
This function moves the flap evenly, distributing the air into the
room.
When the Swing button (D5) is touched, the flap will begin
to move forwards and backwards alternatively.
If touched again, the flap will be locked into its current position.
When the button is next touched, the flap will start to move for-
wards and backwards again.
Please note: in order to avoid damaging the internal mecha-
nisms, the flap must not be moved manually.

SETTING THE TIMER

The timer allows the delayed start up or shut down of the appli-
ance. This function will prevent wasting electricity by optimising
the operating periods.
How to program delayed shut down
• While the appliance is on in any operating mode, delayed
shut down can be programmed.
• Touch the timer button (D8): the timer symbol
(C15) and hours (C16) light up.
• Touch the (D3) and
number of hours to shut down appears on the display.
(D4) buttons until the desired
A few seconds after the timer is set, the setting is acquired, the
display shows the operating mode and the timer symbol stays lit.
Once the set time is elapsed, the air conditioner goes into Standby.
To cancel the timer program, touch the
twice. The timer symbol (C15) will go off.
Please note: Once the timer has been activated, by touching the
timer button only one time, the remaining hours to shut down
will be displayed.
How to program delayed start up
• Plug in the appliance and set to standby.
• Touch the timer button (D8): the timer symbol (C15)
and hours (C16) light up.
• Touch the (D3) and
number of hours to start up appears. Start up can be pro-
grammed at any time within the 24 hours that follow.
When the set time is elapsed, the appliance will start to operate
in the same operating mode that was previously set.
To cancel the timer program, touch the timer button (D8) twice.
The timer symbol (C15) will go off.
Please note: Once the timer has been activated, by touching the
timer key only one time, the remaining hours to the start up will
be displayed.
REPEAT PAIRING OF CST REMOTE CONTROL
The CST remote control is already paired to the bundled Pinguino
appliance. In case the user wants to perform a pairing with an-
other Pinguino device, or in case of a pairing of brand new CST
remote control, the user needs to put the unit in Stand-by mode
and keep touched for 10 secs the MODE selection button (D2) on
the CST remote control. The Led (D10) starts blinking periodi-
cally indicating the pairing phase.
The user is then asked to press for 10 sec the MODE button (C2)
on the Pinguino unit until a double beep is emitted. The pairing
phase is signaled on display by means of a fast flashing of the
dot in the middle of the digits.
When the two devices complete the pairing dialogue, the PAC
emits a double 'beep' , the display will show the normal visualiza-
tion for Standby.
The pairing must be done within 60 sec.
FCC AND CANADA EMC COMPLIANCE INFORMATION
This device complies with Part 15 of the FCC Rules. Operation is
subject to the following two conditions:
(1) This device may not cause harmful interference, and
(2) This device must accept any interference received, including
interference that may cause undesired operation.
Please note: This equipment has been tested and found to com-
ply with the limits for a Class B digital device, pursuant to part 15
10
timer button (D8)
(D4) buttons until the desired