Publicidad
Release handle by stepping on pedal and lowering handle until motor starts.
To lower the handle further, step on pedal again and lower handle as much as
necessary (fig 4).
Use short back and forth strokes to cover small areas at on time.
To switch off raise handle to vertical position.
The necessary time to properly clean a carpet depends on the carpet thickness
and the amount of soil.
To store your upright, roll the cable trying not to twist it and then, either hang it
from the upper hanger of the handle tube (if so equipped), or roll it over both
hangers of the handle tube and fasten it with the clip integrated to the plug.
HEIGHT ADJUSTMENT
The upright has an infinitely variable height adjustment that raises or lowers the
front of the unit. This will allow for better contact with the carpet as needed.
On short or industrial carpet the adjustment knob should be placed to the left,
on shag or heavier rugs the knob should be placed to the right.
To displace knob, pull handle tube backwards until the front is off the ground.
HOW TO REPLACE THE PAPER BAG. ("Z" MODELS )
Unplug upright before replacing bag. Change paper bag frequently, some fine particles can block the airflow and affect
suction power even before the bag appears full. For this reason the bag may need to be changed frequently when vacuuming
fine dust, paste dust or fine substances (bag part No. 45-0315-7).
1. Release bag spring, turn lock to release coupling and remove the bag completely.
2. Unzip bag, lower spring to release the paper bag tube, remove tube and paper bag.
3. Place new bag, slip spring over bag and tube making sure the zipper print on the bag faces the zipper on the cloth bag.
4. Clean upright exhaust every time the bag is changed.
5. Install bag in functioning position with print facing handle.
HOW TO CLEAN PERMANENT BAG: (ALL EXCEPT THE "Z" MODELS)
Unplug upright before emptying permanent bag.
1. Release spring, turn knob to liberate coupling and remove bag assembly.
2. Pull bag clip sideways to release bag. Open bag, place in garbage bag and empty by shaking the bag.
3. Replace clip making sure the bag is closed correctly.
4. Clean exhaust every time bag is emptied.
5. Place bag in operating position making sure it is correctly secured.
6
HOW TO USE
STORE
FIG. 4
HEIGHT ADJUSTMENT
FIG. 5
MAINTENANCE
Unplug upright before replacing belt. Belt may be hot if recently
used.
WARNING: Improper installation of belt or brush roll may damage
upright.
OPERATE
1. Release handle by depressing foot pedal, lower handle tube
and turn upright over (fig 6).
2. Remove bar by pressing on side until it is released.
3. Take belt off fan nut, pull brush roll out, remove and replace
CLEAN UNDER
belt.
4. Replace brush roll making sure both bearing supports face
upwards (top).
5. Replace belt on nut making sure the belt is twisted to the right
as shown on chassis diagram (fig 8).
6. If you need to change the band, it is convenient that you clean
the roller and the fan as well. It is common that the roller
accumulates threads in the ball bearing holders. Take the ball
bearing holders out by pulling them outward and then clean
the ball bearings. To set them back, put them in the same
place and press inward on both sides until they reach their
original position. Clean the fan by removing the dirt, and then
reinstall the following components as described: lid, ventilator
and band.
HOW TO REPLACE THE LIGHT BULB (MODELS U-240, U-530, U-530-Z)
Unplug upright before replacing bulb.
1. Remove bag and handle tube from yoke socket.
2. Remove screw from height adjustment knob. Remove
knob.
3. Turn upright over, with pliers remove springs from chassis
(fig 6).
4. Hold upright cover, turn over and remove cover.
5. Remove bulb pulling on it while moving side to side. The
bulb does not unscrew.
6. To place new bulb press into socket (fig 9).
7. Replace cover, turn upright over and replace springs.
8. Replace height adjustment knob with screw.
Unplug upright before replacing fan.
1. Hold on the fan, with a hand, using a glove, to avoid
any movement.
2. With a 3/4 key, unscrew the pulley nut.
3. Remove the fan and place the new one, make sure
that the bag knob spacer and the fiber washer are
in the right position (see drawing).
HOW TO REPLACE BRUSH ROLL BELT
RETAINER
BAR
BRUSH
FIG. 6
ROLL
MOTOR
COVER
FIG. 7
LOW SIDE OF BELT
FIG. 8
FAN
RETAINER
BAR
COVER
BRUSH
BOTTOM
ROLL
PLATE
FIG. 6
HOW TO REPLACE THE FAN
FAN
COVER
BELT
MOTOR
NUT
BELT
HIGH SIDE OF BELT
HEADLIGHT
BULB
FIG. 9
pulley nut
fiber washer
fan
fiber washer
spacer
motor shaft
7
Publicidad
