DeWalt T1000 Manual De Instrucciones De Funcionamiento página 6

Model T1000
caused local hardening of the steel.
15. Do not fasten through a predrilled hole unless proper guidance
is provided.
16. If you decide not to make a fastening after the tool has been
loaded, you must always remove the powder load first followed
by the fastener.
17. Never attempt to override the safety features of this tool.
hanDling The Tool anD powDeR loaDS
1. Never leave a loaded tool unattended. Once the tool is loaded,
make the fastening immediately or unload the tool.
2. Always unload the tool before work breaks, changing parts,
cleaning or servicing, and when storing.
3. To prevent accidental discharge of loads, never carry the powder
loads in the same container as the fasteners or other hard objects.
4. Always store the powder loads in the containers provided or
in an enclosure provided for them. Never intermix the various
power levels. keep them segregated in clearly identified
containers.
5. Powder loads should never be used in firearms. They are
normally more powerful that the cartridges supplied with the
firearms.
6. Powder actuated tools and powder loads should always be
stored under lock and key. Tools must be unloaded when not in use.
Tool MalFuncTion
1. In the event that a load fails to discharge after the trigger
is pulled, the tool must be kept depressed against the work
surface for a minimum of 30 (thirty) seconds in case of a
delayed load discharge. Then carefully remove the entire load
strip. and dispose of it in a can of water or other nonflammable
liquid. Never attempt to force or pry a load out of a tool
chamber.
2. Never discard unfired powder loads into a trash container.
3. Do not attempt to unload or disassemble a jammed, stuck or
broken tool as improper handling may cause it to discharge
and strike operator and/or bystander. A jammed tool must be
pointed in a safe direction at all times. Tag the tool and lock
it up. Call your D wALT fasteners representative for proper
E
assistance.
FasTener selecTion Guide
300 heaD DiaMeTeR DRive pinS
CAT ShANK STD.
NO. LENGTh BOx
DDf3011000 1/2" k 100
DDf3011050 5/8" k 100
DDf3001100 3/4" 100
DDf3001150 1" 100
DDf3001200 1-1/8" 100
DDf3001250 1-1/4" 100
DDf3001300 1-1/2" 100
DDf3001350 1-3/4" 100
DDf3001400 2" 100
DDf3001450 2-1/4" 100
DDf3001500 2-3/8" 100
DDf3001550 2-1/2" 100
DDf3001600 2-3/4" 100
DDf3001650 3" 100
T1000
STD. hEAD ShANK WT./
CTN DIA. DIA. 100
5000 .300 .143 .5
5000 .300 .143 .5
5000 .300 .143 .5
5000 .300 .143 .6
1000 .300 .143 .7
1000 .300 .143 .8
1000 .300 .143 .9
1000 .300 .143 1.1
1000 .300 .143 1.2
1000 .300 .143 1.2
1000 .300 .143 1.3
1000 .300 .143 1.4
1000 .300 .143 1.6
1000 .300 .143 1.9
.300 heaD DiaMeTeR DRive pinS wiTh Top haT
CAT ShANK STD.
NO. LENGTh BOx
DDf3031000 1/2" k 100
DDf3031050 5/8" k 100
DDf3031100 3/4" 100
DDf3031150 1" 100
.300 heaD DiaMeTeR STep Shank pinS
CAT ShANK STD.
NO. LENGTh BOx
DDf3041000 3/4" Step Shank 100
DDf3041050 1" Step Shank 100
.300 heaD DiaMeTeR DRive pinS wiTh 3/4" waSheR
CAT ShANK STD.
NO. LENGTh BOx
DDf3051100 3/4" 100
DDf3051200 2-1/2" 100
. 300 heaD DiaMeTeR DRive pinS wiTh 7/8" waSheR
CAT ShANK STD.
NO. LENGTh BOx
DDf3061150 1" 100
DDf3061250 1-1/4" 100
DDf3061300 1-1/2" 100
DDf3061400 2" 100
DDf3061550 2-1/2" 100
DDf3061650 3" 100
.300 heaD DiaMeTeR DRive pinS wiTh 1" waSheR
CAT ShANK STD.
NO. LENGTh BOx
DDf3071000 1-1/4" 100
DDf3071050 1-1/2" 100
DDf3071250 2" 100
DDf3071150 2-1/2" 100
DDf3071200 3" 100
.300 heaD Dia. DRive pinS w. 1-7/16" inSulaTion waSheR
CAT ShANK STD.
NO. LENGTh BOx
DDf3081000 1-1/2" 100
DDf3081050 2-1/2" 50
1/4"-20 ThReaDeD STuDS
CAT ThREAD ShANK
NO. LENGTh LENGTh
DDf3811020 1/2" 1/2"k
DDf3811000 3/4" 1/2"k
DDf3811050 3/4" 3/4"
DDf3811100 1/2" 1"
DDf3811150 3/4" 1"
DDf3811180 1/2" 1-1/4"
DDf3811200 3/4" 1-1/4"
DDf3811250 1-1/4" 1-1/4"
6
Cat. No. DDF211001P
STD. hEAD ShANK WT./
CTN DIA. DIA. 100
5000 .300 .143 .5
5000 .300 .143 .5
5000 .300 .143 .5
5000 .300 .143 .6
STD. hEAD ShANK WT./
CTN DIA. DIA. 100
1000 .300 .143/130 .5
1000 .300 .143/130 .6
STD. hEAD ShANK WT./
CTN DIA. DIA. 100
1000 .300 .143 1.6
1000 .300 .143 2.5
STD. hEAD ShANK WT./
CTN DIA. DIA. 100
1000 .300 .143 1.9
1000 .300 .143 2.0
1000 .300 .143 2.1
1000 .300 .143 2.4
1000 .300 .143 2.7
1000 .300 .143 3.0
STD. hEAD ShANK WT./
CTN DIA. DIA. 100
1000 .300 .143 2.2
1000 .300 .143 2.3
1000 .300 .143 2.6
1000 .300 .143 2.9
1000 .300 .143 3.2
STD. hEAD ShANK WT./
CTN DIA. DIA. 100
1000 .300 .143 2.1
500 .300 .143 2.7
STD. STD. hEAD ShANK WT./
BOx CTN DIA. DIA. 100
100 5000 1/4" .143 .8
100 1000 1/4" .143 1.1
100 1000 1/4" .143 1.2
100 1000 1/4" .143 1.2
100 1000 1/4" .143 1.4
100 1000 1/4" .143 1.4
100 1000 1/4" .143 1.5
100 1000 1/4" .143 1.7