To complete installation of the roadside panel, open the battery compartment on the electronic box , box and
insert four 1.5 V alkaline LR20 batteries. , Be sure to follow the polarity markings. Close the battery compartment
and put the electronic box cover back in place with the 6 cross-head screws (H), Take care not to pinch or damage
the seal. You can use a low voltage supply power source, coming from a type WETR 14602 SER.R1 transformer or
from an automatic gate opener (12 ou 24 V / ). It should be connected on the terminals
tronic cabinet. In the case of direct voltage (V ) pay attention to the polarity +/-.
Warning :
If you do not use the batterie but by 12/24 V /
indicated Fig. 10
If you are using a 12/24 V /
power source, the batteries must be removed.
Do not use rechargeable batteries.
6. OPERATION
Warning :
If you try your video door phone before installing it (short distance trial) respect a minimum
of 3 m distance between the monitor and the roadside panel (risk of saturation).
The monitor must be in standby mode, the indicator PWR/REC turned blue. (this mode is activated with
must be installed on a stable surface, with the antenna unfolded. When the Call button is pressed on the roadside
panel the monitor will ring for approximately 8 seconds.At the same time, a tone will sound on the roadside panel
to confirm that the call has been sent. You have approximately 30 seconds to answer the call. At this time, the
electronic box enters standby mode. If the electronic cabinet is powered by a 12 or 24 VDC/AC source, you can
force the communication with the roadside panel pressing the
the call is lost.
The conversation is established during a call pressing the
The system will time out after 60 seconds. To extend this time for an additional 60 seconds, press the Answer
buttons
&
. You can end the communication pressing
1•
If used with an electric strike plate (or electric lock) :
The electric strike plate can be opened only when communicating with a caller(all the time if the electronic
cabinet is powered by external AC/DC supply), To open it, press the
Caution :
One single opening control is possible per call under operation on battery.
N.B. :
The strike plate or lock must be «one pulse type» in order for the door/gate to be opened.
2• If used with an automatic opener :
: An automatic gate opener may be operated via remote control If the electronic cabinet is powered
Caution
by external AC/DC supply. To open it, press the
Reminder
:The reception of a call on the monitor is only possible if it is in standby mode and paired with the
roadside panel (see chapter Pairing).
Important :
The handset has a free-field range of up to approximately 300 metres. This range may be conside-
rably reduced by certain environmental factors (nearby radio interference, etc.)
If you do not use the batterie but by 12/24 VAC/DC
source (automatic opener) to connect as indicated
opposite.
Caution :
In the case of a continuous tension
(VDC) please respect a polarity +/-.
CFI EXTEL WEVPSF 659 - 10/2011
GB10
-
~
+
~
and
of the elec-
source (automatic opener) to connect as
key. If the electronic cabinet is battery-powered
. key
for 2 seconds.
.
.
fig.10
LOCK
+
-
7. KNOWING SCREEN ICON
a. Signal indicator
b. Visiting record indicator (On)
c. Outdoor unit battery indicator
- Full Battery (yellow)
- Low Battery (red/twinkling)
d. Recording indicator
e.
: no SD card
F : Full SD card
Err. : SD card error
: SD card locked
: SD card overwrite
f. SD card indicator
g. SD card storage room indicator
h. No signal indicator
i. Answering indicator
j. Record time
k. System time
) It
8. KNOWING THE MAIN MENU
Press
menu to display the following screens (
a. Camera Setup
c. Event List
to scroll,
to validate)
b. Recorder Setup
d. System Setup
CFI EXTEL WEVPSF 659 - 10/2011
GB11