Descargar Imprimir esta página

Publicidad

Enlaces rápidos

S id e V ie w Ca me r a
Owner's Manual
Side View Camera
Model:
CM-S500
Embedded Type CMOS IV Camera
Side Back View
Side View Assist Line Image
1.High Quality C OS lmage Sensor for High Resolution & Night Time Visibility
M
2.
Side View Assist Line ON / OFF Selectable
3.Automatic Sensitivity Compensation
4.Water Resistant with IP67-IP68 Standard
Remove protective lens covering prior to use.
Be cautious when mounting camera and or wiring near fuel tank.
System is designed for +12 volt DC systems only.
规格:445.5*210MM ,120G双胶纸,双面黑色印刷,成品三折
English-1
Control Box
DVD Screen Control Cable(Blue)
GND (Black)
ACC (Red)
Turning Lamp Control Cable (Pink)
Make Solid Connection
To Chassis Ground
1) Locate a flat surface on the bottom edge part of the side mirror. (See Image 1)
2) Remove the mirror
3) Find an open area to feed the wire through the hole.
4) Make sure there is enough wire and no wire loop inside the mirror that can get caught by the motor.
5) Establish connections (ACC, Turn signal, Video RCA and Ground)
6) Power the camera ON and check the monitor for the picture.
7) While looking at the monitor, angle the camera. Recommended angle is 45-60 Degrees from the vehicle (See Image 2)
8) After adjusting, stick the camera under the side mirror.
9) After sticking the camera under the side camera, installer can adjust the actual camera using the supplied "U-Shape" tool.
(See Image 3 & 4)
10) Make sure the guidelines is evenly running down on the side of the car matching ( See Image 5 )
11) Installer should measure what each line represents. Ex: Distance between ORANGE line and RED line
12) Make sure to check all the functions first before assembling the side mirror and panels back.
*
Gridlines can be disabled if it does not match the vehicle's specs
Image(1)
Angle Adjuster
(Tool)
Image(3)
Angle Adjuster
(Tool)
Image(5)
English-2
Camera
3.3V Input
3.3V Output
Right Side View Assist Line
ON/OFF Selectable
Turning Lamp Control Cable (Pink)
Manuel d'Utilisateur
Assist Line for Right Side View
Side Back View
Spécifications :
Image(2)
Angle Adjuster
(Tool)
Caractéristiques du Produit:
Image(4)
1.Capteur d'Image CMOS de Haute Qualité pour Haute Résolution et Vision Nocturne
2.Sélection d'Image Mirroir / Standard
3.Compensation de Sensibilité Automatique
4.Résistant à l'Eau avec norme IP67-IP68
Angle Adjuster
Mises en Garde:
(Tool)
Image(6)
Enlever le protecteur de lentilles avant l'utilisation.
Prenez garde lorsque vous installez la caméra et/ou le filage près du réservoir à essence.
Système conçut pour système +12 volts DC seulement.
Ca mé r a d e V is io n A r r iè r e
Side View Camera
Model:CM-S500
Caméra de Type Intégrée CMOS IV
French-1

Publicidad

loading

Resumen de contenidos para Rydeen CM-S500

  • Página 1 2) Remove the mirror 3) Find an open area to feed the wire through the hole. Model: CM-S500 Model:CM-S500 4) Make sure there is enough wire and no wire loop inside the mirror that can get caught by the motor.
  • Página 2 Side View Camera presente Imagen eliminado Model:CM-S500 Options de Positions pour l'Installation de la Caméra : Cámara Posición de instalación Opciones : La caméra peut être positionnée soit sur le côté inférieur du couvert de valise, soit sur la paroi du Cámara incrustado CMOS Tipo IV...