Assembly/Adjustment - Lista CBE450L Traducción De Las Intrucciones Originales

OPERATING
INSTRUCTIONS
NOTE: Before using the tool, read the
instruction book carefully.

ASSEMBLY/ADJUSTMENT

WARNING! The guard must always be
on the tool to protect the user.
1. FITTING THE GUARD (SEE FIG A)
Locate the guard to the motor housing, note
orientation. Secure in place using four screws
supplied assembled on the guard. Check the
guard is properly located and secure.
WARNING! Take great care when doing
this as the guard has a very sharp cutting
edge. (See fig B)
WARNING! Never operate the tool without
the guard properly in place. Use of the unit
without having installed the guard will cause the
motor to overheat, and void the warranty.
2. FITTING THE AUXILIARY HANDLE (SEE FIG
C1,C2)
NOTE: This may already be pre-fitted to the
trimmer. However the following instructions give
full assembly details.
1. Unscrew the auxiliary handle locking knob
(counterclockwise) and remove from handle.
2. Position auxiliary handle onto handle bracket
assembly located on trimmer's shaft.
3. Position the knob and screw through the
auxiliary handle and bracket, and tighten knob
(turn clockwise). Do not tighten completely until
you have adjusted the auxiliary handle to your
desired working position.
3. ADJUSTING AUXILIARY HANDLE (SEE FIG
D)
Unscrew the auxiliary handle locking knob.
The auxiliary handle's bracket can be moved up
or down on the shaft and the auxiliary handle itself
can be moved forward or backward into 5 different
locked positions
Then tighten the auxiliary handle locking knob.
4. ADJUST THE HEIGHT (SEE FIG E)
To adjust the telescopic shaft. simply push the
height adjustment locking collar apart and push
the bottom section of the shaft down to the desired
height. It will click into one of the notches on the
shaft, and lock into place. Release both collars to
lock the shaft into place.
28
5. ROTATE THE REAR HANDLE AND UPPER
SHAFT 1800 (SEE FIG F. G)
Pull Handle rotation locking collar and turn the top
of the shaft 1800 counter-clockwise (The head will
only move in one direction). Release the locking
collar to lock shaft in place.
6. ADJUST THE CUTTING ANGLE (SEE FIG H)
Your trimmer has a four position tilting head. This
can be adjusted to achieve a comfortable and
efficient working angle. This allows controlled
trimming around flowerbeds, under shrubs, around
trees and fence posts etc.
To change the angles simply depress the flattening
head adjustment button and move the motor head
to desired position, then release the button.
WARNING! Always disconnect the trimmer
before making adjustments!
7. MAINS SUPPLY CABLE STRAIN RELIEF
(SEE FIG I)
In order to reduce strain on the cable inlet, form a
loop and locate the cable around the strain relief
arm.
8. ON/OFF SWITCH
To start, press and hold the switch. Release the
switch to stop.
WARNING! The cutting head continues to
rotate after the trimmer has been switched
off, wait until it has stopped then lay down the tool.
OPERATION
WARNING: Always wear the eye protection.
Never lean over the trimmer head. Rocks
or debris can ricochet or be thrown into eyes and
face and cause blindness or other serious injury.
When operating unit, check for the following:
Wear eye protection and heavy clothing. Hold front
handle with one hand and auxiliary handle with
the other hand. Keep unit below waist level. Work
only from your right to your left to ensure debris is
thrown away from you. Without bending over, keep
line near and parallel to the ground (perpendicular
when edging) and not crowded into material being
cut.
WARNING: Make sure that line is fed out
before operation. Make sure motor is up
to full speed before trimming.
WARNING: Use only 1.45mm diameter
cutting line. Other sizes of line will not feed
properly and will result in improper cutting head
function or can cause serious injury. Do not use
other material such as wire, string, rope, etc.
Wire can break off during cutting and become a