Emerson insinkerator indulge Serie Instalación, Cuidado Y Uso página 6

5
INSTALLING FILTRATION SYSTEM
A
Personal Injury: Do not locate filter above an outlet or other
electrical device. Install head and bracket so that connections
require no stretching, kinking or pinching of tubing.
B
from water
supply line
Property Damage: Tube runs need to form to the cabinet's
contours to allow storage space with no sharp bends. Tubes
need clean, perpendicular, burr-free cuts to ensure a true fit.
C
HC1100, HC2200, GN1100, GN2200, GN2215,
HC2215 HC3300, H3300
From filter or From filter or
water supply line water supply line
Property Damage: Do not extend the
lines farther than the 16" provided.
D
Discharge tube
To dispenser
From water
supply line
It is normal for approximately 2 oz. of water to
discharge when filter is removed.
10
Screws provided are for use in wood
studs or cabinets only. Use wall anchors
(not supplied) for installation into drywall.
Mark hole locations for filter head
and bracket in a spot that allows
for filter replacement.
Drill 1/8" starter holes and attach bracket
to wall with wood screws, turning until snug.
Remove red filter cap, insert filter
cartridge into filter head and twist
clockwise until "LOCK" arrow on the
filter aligns with arrow on bracket.
Determine length of tubing required,
then cut to length making sure the cut
is perpendicular and burr-free.
Insert a white 3/8" tube into inlet side
to dispenser
of filter head until it stops.
Press in again to ensure a secure fit.
Insert the other white 3/8" tube into
outlet side of filter head until it stops.
Press in again to ensure a secure fit.
Insert the copper tube(s) from the
dispenser into quick-connector using
"Y" connector for hot and cool models or
straight connector for hot-only models.
Connect the white 3/8" tube from the
right outlet on the filter head into the
quick-connect fitting until it stops.
Press in again to ensure a secure fit.
To remove tube(s) or plug from quick-connector,
depress the release ring and gently pull away.
To redirect filter replacement water
discharge, place 6" clear tube over
vent hole on the left side of filter head.
Note: 3/8" fitting is required to make
connection to water supply.
Connect remaining white 3/8" tube to
incoming water supply line.
(See Step 6.)
6
FINAL WATER CONNECTION
A
Brass Nut
Ferrule
Brass Insert
Plastic
tube
Property Damage: Join remaining tube
to cold water supply only.
B
Scalding Hazard: The faucet dispenses near-boiling
(212ºF) water which can instantly cause scalds or
burns. Use care when operating this appliance.
Dispensing Hot Water Dispensing Cool Water
(HC3300, H3300) (HC3300)
Scalding Hazard: The faucet dispenses near-boiling
(212ºF) water which can instantly cause scalds or
burns. Use care when operating this appliance.
C
Property Damage: A standard grounded outlet within
30" of the dispenser is required under the sink. Do
not use an extension cord set with the dispenser.
If the water coming from the faucet is not hot 15 minutes after the unit has been
plugged in – or for other issues related to the operation of your instant hot water
dispenser – refer to the "Troubleshooting" section on Page 15.
I I
Install a T-fitting (not included)
onto the cold water supply line.
I I
Install dedicated water control valve
with 3/8" compression fitting.
I I
At the end of the white 3/8" tube from the
filter or quick-connector, slide the supplied
brass nut and ferrule over the tube and
then push in the brass tube insert.
I I
Insert the white 3/8" tube into the 3/8"
compression fitting and tighten.
I I
Turn on the water supply.
I I
Depress the dispenser's HOT handle
and hold it until water flows from the
spout (approximately 1 to 2 minutes).
Note: See box below for special
instructions on operation of
InDulge TM Modern faucets.
I I
Run the water for at least 2 minutes to
flush lines (both the hot and cold handles
independently if applicable).
Operating Instructions for InDulge TM Modern Faucets
I I
HC3300: To dispense instant hot water,
first press down on the faucet handle
and then push the handle in the direction
of the red indicator on the top of the
handle: back in a right-hand installation
or forward in a left-hand installation. To
dispense cool water, move the handle in
the opposite direction, toward the blue
indicator on the handle.
I I
H3300: To dispense instant hot water,
first press down on the faucet handle
and then push the handle back in a
right-hand installation or forward in a
left-hand installation.
I I
Check all connections to ensure they are
tight and that there are no leaks.
I I
Plug in instant hot water tank.
Water will be cold at first.
Allow 12-15 minutes for water to reach
target temperature.
Gurgling or hissing is normal during the
initial heating cycle.
11