Rear Panel - Phonic POWERPOD 1860 PLUS Manual Del Usuario

10. Power Amp Inputs
These inputs support 1/4" TS plugs and can be used for the
inclusion of an external line level stereo signals to the built-
in power amplifier. If a device is connected to the power amp
inputs, the main feed (according to the power amp control
switch) will automatically bypass the power amp and the
inserted feed will be amplified and sent to the Speaker Outputs
instead.
11. Main Outputs
These two ports will output the final stereo line level signal sent
from the main mixing bus. The primary purpose of these jacks
is to send the Main output to external devices that may run
in parallel with the mixer. This may include additional power
amplifiers, mixers, PA systems, as well as a wide range of other
possible signal processors.
12. Auxiliary (AUX) Outputs
These phone jack outputs are the final output of line-level signal
fed from the corresponding auxiliary mixing bus, and are best
suited for use with stage monitors. Feeding the output from the
Auxiliary outs to an amplifier - and possibly an equalizer - and
then to a floor monitor speaker allows artists to monitor their
own instruments or vocals whilst performing.
13. EFX (Effect) Outputs
These 1/4" TS outputs are the final output from the EFX send
mixing bus. This feed may be used to connect to an external
digital effect processor, or even to an amplifier and speakers,
depending on your desired settings.
10
11
14. Control Room / Zone 2 Outputs and Switch
These phone jack outputs feed the signal from either the
control Room or zone 2 control panels. The corresponding
switch alternates the feed between the audio from the cTRl
RM/PHONES control and that of the zone 2 control. The zone
2 output is best suited to act
as side fill, supplying audio
to indoor areas that the sound
from the main speakers does
not reach. The control room's
signal, on the other hand, can
be used for the inclusion of an
active monitor within a booth.
Well, they're our suggestions,
but it's your call.
15. Mono Output
This 1/4" TS output feeds the audio signal from the mono
mixing control located on the main mixing panel. This is best
suited for use with a mono sound system, or for the addition of
a subwoofer to your set of speakers, adding more punch to low
frequency sounds.
16. Phones Output
This stereo output port is suited for use with headphones,
allowing monitoring of the mix. The audio level of this output is
controlled using the cTRl RM/PHONES control.
4
12 13
14
15 16

Rear Panel

17. Voltage Selector
This switch allows you to select from
2 mains power modes, 115 Vac / 60
Hz (allowing you to use the device in
countries with voltages between 100V
and 120V) or 230 VAC / 50 Hz (allowing
you to use the device in countries with
voltages between 200V and 230V).
NB. Using incorrect voltages can cause
irreversible damage to the mixer. all care must be taken in selecting the
voltage appropriate to your zone. If unsure of local voltage levels, contact
a knowledgeable source before using this mixer.
18. 12V Lamp
This XlR port allows you to attach a 12 Volt gooseneck lamp,
allowing better visibility in areas with poor light.
19. Power Button
This button is used to turn
t h e d e v i c e o n a n d o f f .
Before turning the device
on, however, ensure all level
controls are at a minimum.
20. Mains Power Inlet
This port is used to plug the
socket end of the included
ac cable. The other end
should be connected to an
appropriate power source.
21. Speaker Outputs
These jacks are used to connect to speakers, fed from the
internal power amp. The first set of outputs are professional
speaker connectors; to use these, insert an appropriate four pin
plug into the connector, and twist to lock into place. The second
set of outputs are 1/4" phone jacks. To use these, simply insert
an appropriate 1/4" TS plug into them. The total loading for
speakers should be no more than 4 ohms per channel, or 8
ohms for a bridge mono connection.
21
One Speaker per Channel: When connecting a single speaker
to each channel's output, speakers with an impedance between
4 and 8 ohms should be used. This is the case for both the
Phone Jack and Professional Speaker connectors.
Two Speakers per Channel: When connecting two speakers
to the Speaker Outputs, the loading of each speaker should
be between 8 and 16 ohms (as two 8 ohm speakers will form a
total loading of 4 ohms, two 16 ohm speakers a total loading of
8 ohms, etc).
Bridge Mono: When using bridge mono mode, Professional
Speaker output B should be used only. The total loading should
be no less than 8 ohms.
NB. Only use passive speakers in conjunction with the Speaker outputs,
as to avoid damaging any equipment.
POWERPOD 1860
18 17
20
19
/ K-12 / K-16