EDG 101204 Manual De Instalación, Uso Y Mantenimiento página 8

Single-phase 230 V power supply
circuit breaker or fuse (not supplied)
ground
Phase
Neutral
- Connect the heat pump to a suitable electric power supply. The voltage must correspond to the
machine's nominal voltage.
- Connect the ground.
- Depending on the location, install any required lightning-proof devices.
- Protect the circuit with a suitable circuit breaker or fuse.
- The power cable and the signal cable must not come into contact. Otherwise interference with the
control signals may occur.
Special cases Special cases Special cases Special cases
In the event of an unexpected power cut, the heat pump automatically restarts. Check the
settings and adjust if necessary.
In the event of an expected power cut, switch off the heat pump. As soon as the power is
restored, switch on the pump, check the settings and adjust if necessary.
Always switch off the machine in stormy weather.
USE USE USE USE
Preparing the pool (first use) Preparing the pool (first use)
Preparing the pool (first use) Preparing the pool (first use)
- Fill the pool with mains water. Avoid using well water which may have variable and unknown
characteristics. If you cannot use mains water, use the EDG anti-scaling product that will prevent any
possible discomfort.
- Clean the pool, the skimmer and pump pre-filters and backwash the filter.
- If the sand in the filter is more than five years old, replace it or clean using a filter anti-scaling agent by
EDG range.
- Adjust the pH to 7 – 7.4 using EDG PH – or EDG PH +.
- Add the MOONCAL by EDG anti-scaling agent.
- Proceed with shock treatment using EDG liquid active oxygen (1 litre per 10m3).
Always observe the filtering times according to the temperature in order to save the disinfecting
products.
Always stop the pump before working on the filter valve and then switch it on again. Always stop the pump before working on the filter valve and then switch it on again. Always stop the pump before working on the filter valve and then switch it on again. Always stop the pump before working on the filter valve and then switch it on again.
The chemical parameters of the water are maintained in the following ranges: The chemical parameters of the water are maintained in the following ranges:
The chemical parameters of the water are maintained in the following ranges: The chemical parameters of the water are maintained in the following ranges:
Acidity pH 7.00 – 7.80
Shock chlorine ppm max 15 for 24 hours
Bromine ppm 2 – 3
PHMB ppm 20 – 50
Total alkali strength °F 8 – 12
NOTPACEDG - ind B - 0408
heat pump control
PCB
Free chlorine ppm 1 – 3
Salinity g/l 0 – 5
Ozone ppm 0.8 – 1.0
Hardness °F 10 – 50
15 / 15
DIGITAL CONTROL PANEL SETTINGS DIGITAL CONTROL PANEL SETTINGS DIGITAL CONTROL PANEL SETTINGS DIGITAL CONTROL PANEL SETTINGS
Settings
- Required temperature
- Clock
TIME ON indicator
TIME ON setting
TIME OFF setting
PICTOGRAMS PICTOGRAMS PICTOGRAMS PICTOGRAMS
CLOCK
PERMANENT DISPLAY PERMANENT DISPLAY PERMANENT DISPLAY PERMANENT DISPLAY
- The display shows the time when the machine is turned off.
- The display shows the temperature of the water in the pool when the machine is turned on.
ADJUSTING THE WA ADJUSTING THE WA ADJUSTING THE WATER TEMPERATURE ADJUSTING THE WA TER TEMPERATURE TER TEMPERATURE TER TEMPERATURE
- Press and to adjust the temperature.
The temperature flashes.
- After five seconds, the display stops flashing.
ADJUSTING THE TIME ADJUSTING THE TIME ADJUSTING THE TIME ADJUSTING THE TIME
(can be changed when the machine is on or off)
- Press to adjust the operating times.
- The time flashes. Press the time button
- Press and to change the settings.
- Before the display stops flashing, press
- Press and to change the settings.
- Press and the temperature of the water appears.
- After 30 seconds, the display stops flashing.
AUTOMATIC MODE AUTOMATIC MODE AUTOMATIC MODE AUTOMATIC MODE
TIME ON TIME ON TIME ON TIME ON
- Press to set the time when the heat pump starts.
TIME ON
- When the display comes on and the time flashes, press
- Press and to change the settings. Before the display stops flashing, press
- Press and to change the settings.
- Once you have finished, press
TIME ON
- After 30 seconds, the display stops flashing.
NOTPACEDG - ind B - 0408
Hot
On / Off
Time setting
TIME OFF setting
AUTOMATIC AUTOMATIC STOP
(can be changed when the machine is on or off)
again to change the times.
to set the minutes.
TIME ON again to set the hour.
to set the minutes.
and the temperature of the water appears.
16 / 16