Customer Service - DrBrowns AC178-INTL Instrucciones De Uso

REPLACING HEPA FILTER:
For optimal performance, it is recommended to replace the filter every 6 months of
regular use. Replace the filter by following the steps below.
1. Remove the filter cover from the bottom of the base and take out the old filter.
2. Place a new filter into the base, ensuring the pull tab is still visible on top of the filter.
3. Insert the filter cover back into the base.
NOTE: Filter must always be used to ensure proper performance.
4
D
C
B
A
To purchase replacement filters, visit www.drbrownsbaby.com
4
WARRANTY:
This appliance is warranted against defective material or workmanship for a period of
one year from the date of purchase. Any defective part will be repaired or replaced at
no charge if it has not been tampered with and appliance has been used according to
these printed instructions. This warranty gives you specific legal rights as well as other
rights which vary from state to state.
PLEASE NOTE: This warranty does not cover a defect that has been caused by
negligence, accidents or improper use of the appliance. To keep your Dr. Brown's
Bottle Sterilizer and Dryer in good condition and retain your warranty, USE ONLY
DISTILLED WATER.

CUSTOMER SERVICE

If you experience unsatisfactory operation or have any questions/comments, call
Handi-Craft's Customer Service at 1-800-778-9001, send an email to info@handi-craft.
com, or write to Handi-Craft Company, Customer Service, 4433 Fyler Avenue, St. Louis,
Missouri 63116 USA. Our Customer Service Representative will advise you how to correct
the problem yourself or will ask you to return the product for repair or replacement.
For purchases made outside of the United States and Canada, please contact your local
distributor.
3 2
B
A
DESIGN UNITS: MILLIMETERS
TOLERANCES UNLESS NOTED:
NO PLACE: X
ONE PLACE: .X
TWO PLACE: .XX
THREE PLACE: .XXX
ANGLE: X
2 HEPA Type Filters are included.
ANGLE: .X
THIRD ANGLE
PROJECTION
or contact your local distributor.
3 2
2
1
THIS DRAWING AND RELATED 3D CAD DATA
HANDI-CRAFT COMPANY
CONTAINS PROPRIETARY INFORMATION THAT
ARE THE PROPERTY OF
2.5
HANDI-CRAFT CO. AND ARE NOT TO BE
0.5
4433 FLYER AVE. ST. LOUIS MO. 63116, USA
COPIED OR USED WITHOUT THE PERMISSION
0.25
OF HANDI-CRAFT CO.
0.13
0.5
INTERPET PER ASME Y14.5-1994 DRAWN
RBW
0.25
OTHER HANDI-CRAFT ENGINEERING
STANDARDS MAY APPLY ENG APPR.
SOLIDWORKS 3D
MFG/Q.A APPR.
2
DESIGN UNITS: MILLIMETERS DRAWN RBW 15JUL19
HANDI-CRAFT COMPANY
TOLERANCES UNLESS NOTED:
ENG APPR.
NO PLACE: X 2.5
4433 FLYER AVE. ST. LOUIS MO. 63116, USA
ONE PLACE: .X 0.5 MFG/Q.A APPR.
TWO PLACE: .XX 0.25
TITLE:
THIS DRAWING AND RELATED 3D CAD DATA
THREE PLACE: .XXX 0.13
FILTER REPLACEMENT
CONTAINS PROPRIETARY INFORMATION
ANGLE: X 0.5
THAT ARE THE PROPERTY OF
ANGLE: .X 0.25
HANDI-CRAFT CO. AND ARE NOT TO BE
COPIED OR USED WITHOUT THE
PERMISSION OF HANDI-CRAFT CO.
DO NOT SCALE DRAWING
SIZE C DWG. NO.
INTERPET PER ASME Y14.5-1994
THIRD ANGLE OTHER HANDI-CRAFT ENGINEERING
PROJECTION STANDARDS MAY APPLY
MATERIAL
SOLIDWORKS 3D SCALE: 1:1 SHEET 1 OF 1
1
D
C
B
TITLE:
SIZE
A
MATERIAL
15JUL19
SCALE: 1:2
DO NOT SCALE DRAWING
A
REV. 1
1
B
A
FILTER AND COVER
DWG. NO. REV.
1
SHEET 1 OF 1
1
8