Publicidad
Idiomas disponibles
Idiomas disponibles
Enlaces rápidos
Hitch Shown In Proper Position
Equipment Required: Fishwire (provided)
Fastener Kit: 24856F
F t
Kit 24856F
Wrenches: 5/8", 11/16"
Drill Bits: none
FORWARDS
FORWARDS
PASSENGER SIDE FRAME RAIL SHOWN
1
Qty. (2)
U-BOLT 7/16-20
2
Qty. (4)
CONICAL WASHER – 7/16"
3
Qty. (4)
NUT – 7/16"-20
4
Qty. (2)
CARRIAGE BOLT 7/16"-14 X 1-1/2"
1.
Place the U-bolts in rear most indentation in frame extension as shown.
2.
Raise hitch into place and loosely install the conical washers and 7/16-20 (fine thread) nuts.
3.
Using the fishwire (provided) insert coiled end thru forward attachment hole in hitch, into the frame, and out the access hole. Slide
block on and thread carriage bolt into the coil of the fishwire. Keep block and bolt separate until inside frame (see photo above).
Pull carriage bolt and block into position with the thread showing below hitch side bracket. Install lock washer and 7/16-14
(course thread) nut.
4.
Tighten all fasteners
Note: check hitch frequently, making sure all fasteners and ball are properly tightened. If hitch is removed, plug all holes in trunk pan or other body panels to
prevent entry of water and exhaust fumes. A hitch or ball which has been damaged should be removed and replaced. Observe safety precautions when working
beneath a vehicle and wear eye protection. Do not cut access or attachment holes with a torch.
This product complies with safety specifications and requirements for connecting devices and towing systems of the state of New York, V.E.S.C. Regulation V-5
and SAE J684.
z
2010 Cequent Performance Products
Installation Instructions
Ford Fiesta Sedan
FASCIA
Drawbar Kit:
3593
3593
Drawbar must be used in the
RISE position only.
1
FRAME
EXTENSION
5
4
4
2
2
3
Tighten all 7/16 fasteners with torque wrench to 50 Lb.-Ft. (68 n*m)
5
4
2
3
5
Qty. (2)
BLOCKS – 3/16" X 1" X 2"
6
Qty. (2)
LOCK WASHER – 7/16"
7
Qty. (2)
NUT – 7/16"-14
8
Qty. (-)
-
Sheet 1 of 3
24856N
Part Numbers:
24856
60272
77229
24849 U-Haul
Do Not Exceed Lower of Towing Vehicle
Manufacturer's Rating or
2000LB (908Kg) Max Gross Trailer Weight
200 LB (90.8 Kg) Max Tongue Weight
Wiring Access Location: TBD
FRAME
1
1
5
4
ATTACHMENT
11-16-10
Form F206 Rev A 5605
ACCESS
HOLE
FORWARD
HOLE
67
Rev. B
Publicidad
Manuales relacionados para Cequent Performance Products 24856
Resumen de contenidos para Cequent Performance Products 24856
- Página 1 This product complies with safety specifications and requirements for connecting devices and towing systems of the state of New York, V.E.S.C. Regulation V-5 and SAE J684. Sheet 1 of 3 24856N 11-16-10 Rev. B 2010 Cequent Performance Products Form F206 Rev A 5605...
- Página 2 Ce produit est conforme aux normes V-5 et SAE J684 de la V.E.S.C. (État de New York) concernant les spécifications en matière de sécurité des systèmes d’attelage. Feuille 2 de 3 24856N 11-16-10 Rev. B 2010 Cequent Performance Products Form F206 Rev A 5605...
- Página 3 Este producto cumple con las especificaciones y requisitos de seguridad para conectar dispositivos y sistemas de remolque del estado de Nueva York, V.E.S.C. Regulación V-5 y SAE J684. Hoja 3 de 3 24856N 11-16-10 Rev. B 2010 Cequent Performance Products Form F206 Rev A 5605...