Publicidad
Idiomas disponibles
Idiomas disponibles
OPERATING INSTRUCTIONS
ASSEMBLY INSTRUCTIONS
Before initial use some assembly is required. Attach casters to heater body using
components provided as shown in Fig. 2.
1. Turn the heater (A) upside down. Remove the wing nut (E) from the straight tip of
each U-bolt (B). Hook one U-bolt under the heater base between the heater control
box and the next fin.
2. Align a pedal (D) with the U-bolt tips. Insert the bent tip through one of the pedal
bolt holes. Insert the straight tip through the other hole. Use the removed wing nut to
secure the straight tip to the pedal.
3. Hook the other U-bolt under the heater base between the last two fins. Attach
pedal in same manner as described in previous step.
4. Remove the nuts (C) preassembled to the casters (F). Insert the caster stems
through the caster holes in the pedals. Use the removed nuts to secure the
casters to the pedals. Turn the heater upright.
HEATER OPERATION
Always operate the heater in the upright position following all instructions and
recommendations listed in this manual.
HEATER LOCATION
Place the heater in the area of the room that is coldest.
HEATER CONNECTION
Plug heater directly into 120 volt A.C. 60 Hz outlet. Be sure the
plug fits tightly in outlet. A loose connection may cause
overheating and damage to the plug or heater.
NOTE: To prevent overloading a circuit, do not plug the heater
into a circuit that is servicing other electrical needs.
HEATER STARTUP
1. To start the heater, press one or both power switches (Fig. 3)
from the Off to the Low or Med heat mode positions. When
both switches are pressed the heater will operate in High heat
mode.
2. Turn the Thermostat control counterclockwise as far as it will
go to the maximum (+) position.
POWER LEVEL SWITCHES
Low switch = Low heat mode (600 watts)
Med switch = Medium heat mode (900 watts)
Low + Med switch = High heat mode (1500 watts)
6
OPERATING INSTRUCTIONS
SETTING THERMOSTAT
After heater has been turned on and the area has reached the desired temperature,
slowly rotate the Thermostat Control counterclockwise until the heater shuts off (you
should hear a faint "click"). By leaving the thermostat at this setting the heater will
automatically maintain this area temperature. To maintain a lower temperature, rotate
the control further counterclockwise toward the minimum (-) position. To maintain a
higher temperature, rotate the control clockwise toward the maximum (+) position.
IMPORTANT SAFETY FEATURES
The power indicator light, located in the Power Switch, lights when the heater is
switched on to tell you that the heater has power. The heater is equipped with an
automatic overheat protection device located inside the body of the heater. If the
heater is covered, or if the heater gets too hot for any reason, the automatic overheat
protection device will turn the heater off. The unit must be reset to resume operation. To
reset the unit, turn both power switches to "O" (Off) and unplug the heater. Wait for 10
minutes for the heater to cool down. Plug the heater back in and restart. To prevent
further automatic shut-off, locate the heater far enough away from a wall or other
object to allow for sufficient airflow. Always place the heater on a smooth level surface.
The heater is also equipped with a safety tip-over switch to turn power off to the heater
when the heater tips over. To resume heater functions simply stand heater upright. With
tip over protection, the heater will only operate when placed upright on a level surface.
CARE AND MAINTENANCE
CLEANING
CAUTION:
Before cleaning the heater be sure to disconnect power cord and allow
the heater to cool completely.
The heater should be cleaned at least once a year to maintain proper performance.
Clean the outside surface with a damp cloth. Allow heater to dry completely before use.
Do not use harsh chemical or abrasive cleaners.
Kenmore
WARNING: To prevent personal injury or heater malfunction, NEVER immerse the
heater in water.
CAUTION: Do not operate the heater without the grill in place. Do not use the
heater if it has malfunctioned or become damaged in any way.
Thermostat
REPAIR
Do not attempt to open the heater to clean or otherwise service the inside. If the heater
does not function normally, call the following customer assistance number to arrange
for possible heater service and repair: 1-866-877-1889
High
Low Med
STORAGE AND MOVEMENT
- Keep original carton for long term storage of the heater.
- Unplug and wrap the cord around the cord storage plate when heater is not in use to
Off
avoid damage to cord and plug.
- To roll the heater on its casters, place two or three fingertips beneath the top edge of
the Pull Handle (Fig. 1) and your thumb on top of the handle. Pull the heater forward.
Fig. 3
The plastic handle won't become hot during heater use as will the metal fins and metal
portion of the control box.
CAUTION: DO NOT pull on cord to roll the heater from one location to another. DO
NOT place hands on heater fins to roll heater unless heater is completely cooled down
after use.
7
Publicidad
