Resumen de contenidos para Jennings H-24
- Página 1 H-24 / H-25 USE AND CARE GUIDE Jennings Traditional Swings ™ Questions, problems, missing parts? Please call Customer Service:1-800-800-4950 warranty SH-ZI-5306 10/18 © 2018 Jack-Post Corporation...
- Página 2 H-24 / H-25 Contents Do Not Return ..................03 Use & Care / Wood Care Guide............04 Instructions ...................05 Customer Service Contact Info............11 © 2018 Jack-Post Corporation 10/18...
-
Página 3: Do Not Return
H-24 / H-25 DO NOT RETURN THIS ITEM TO THE STORE If you experience any difficulty with assembly, missing parts or use, DO NOT please return this item to the store. Retail stores are unable to properly assist you. Customer Service Department Contact our directly for assistance. -
Página 4: Use & Care / Wood Care Guide
H-24 / H-25 USE & CARE WARNINGS: THIS PRODUCT DESIGNED FOR A MAXIMUM CAPACITY OF 400 POUNDS. NOTE: Save assembly instruction sheet for future reference. OIL-BASED PAINTED WOOD CARE GUIDE PLEASE READ THIS INFORMATION CAREFULLY - IT WILL HELP YOU TO MAINTAIN YOUR FURNITURE This furniture has been made from seasoned wood and has already been factory primed and finished with an oil-based paint. -
Página 5: Instructions
Balancelle traditionnelle ™ Assembly Instructions – Model H-24 / 25 Instrucciones de armado – Modelo H-24 / 25 Instructions d'assemblage – Modèle H-24 / 25 FINISHING INSTRUCTIONS To preserve and beautify the wooden parts, they should be painted or varnished on all sides before assembly with good quality exterior finish. -
Página 6: Importante
H-24 / H-25 IMPORTANT UNLESS NOTED, DO NOT TIGHTEN ANY BOLTS UNTIL LAST STEP. IMPORTANTE ú ú A MENOS QUE SE LE INDIQUE, NO APRIETE NING N PERNO HASTA EL LTIMO PASO. IMPORTANT À MOINS D'INDICATION CONTRAIRE, NE RESSERREZ PAS LES BOULONS AVANT LA DERNIÈRE ÉTAPE. - Página 7 H-24 / H-25 STEP 1 Position and insert 65 mm screws in 2 holes in back. Place screws through 2 holes in seat using washer and lock nut. NOTE: Do not mount back assembly incorrectly. PASO 1 Posicionar y insertar los pernos de 65mm a través los agujeros del respaldo y del asiento.
- Página 8 H-24 / H-25 STEP 2 Attach each arm to back by placing70 mm screws through chain, thenthrough the hole in tapered end of the arm (straight edge of the arm facing in), then attach to back with a washer and a nut.
- Página 9 H-24 / H-25 STEP 3 Place arm supports between each arm and seat at the front of the swing. Hook link of chain on each side on 12" eye bolts and slide eye bolts through arms, supports, and seat as shown. Using nuts and washers,tighten eye bolts until they indent the surface.This will prevent the chain from coming loose...
- Página 10 Your package contains two eyebolts. These should be screwed into a solid material (ceiling joists) as shown in Figure A. The screws should be spaced 46 inches apart for the H-24, and 58 inches apart for the H-25. Drill a 1/4 inch pilot hole for each eyebolt and lubricate the threads with wax, oil, or soap for easiest installation.
-
Página 11: Customer Service Contact Info
H-24 / H-25 Customer Service Questions, problems, missing parts? Please call Customer Service: 1-800-800-4950 For more information about warranty, please visit WWW.JACK-POST.COM / Warranty . CORPORATION 800 East Third Street Buchanan, Michigan 49107-1803 Customer Service 1-800-800-4950 Mon. thru Fri. 8:00am – 8:00pm EST E-mail cs@jack-post.com...