Ego Power+ CS1400E Manual Del Operador página 12

8. Lift the tip of the guide bar up to check for sag
(Fig. K). Release the tip of the guide bar and turn the
chain tensioning knob clockwise. Repeat this process
EN
until the sag is eliminated.
9. Tighten the side cover knob securely to ensure that
the saw chain is properly tensioned before using.
Fig. J & L parts description see below:
J-1 Chain Drive Links
J-2 Guide Bar Groove
L-1 Alignment Flange
NOTICE: To extend the guide bar life, invert the bar
occasionally.
NOTICE:
If chain is too tight, it will not rotate. Loosen
the side cover knob slightly and turn the tensioning knob
once from right to left. Lift the tip of the guide bar up and
retighten the side cover knob securely. Assure that the
chain will rotate without binding.
ADJUSTING THE CHAIN TENSION
Stop the motor and remove the battery pack before
adjusting the chain tension. Make sure the side
cover knob is loosened. Turn the chain tensioning
knob clockwise to tension the chain. See the section:
"REPLACE THE BAR AND CHAIN" for additional
information.
A cold chain is correctly tensioned when there is no slack on
the underside of the guide bar and the chain is snug, but it
can be turned by hand without binding. The chain must be
re-tensioned whenever the flats on the drive links do not sit
in the bar groove.
During normal saw operation, the temperature of
the chain will increase. The drive links of a correctly
tensioned warm chain will hang approximately 1.3 mm
out of the bar groove (Fig. M).
NOTICE:
New chains tend to stretch; check chain tension
frequently and tension as required.
NOTICE:
A chain tensioned while it is warm may be too
tight upon cooling. Check the cold tension before next use.
OPERATION
WARNING:
Do not allow familiarity with this product
to make you careless. Remember that a careless fraction
of a second is sufficient to inflict serious injury.
WARNING: Always wear eye protection with side
shields. Failure to do so could result in objects being
thrown into your eyes and other possible serious injuries.
12
56 VOLT LITHIUM-ION CORDLESS CHAIN SAW — CS1400E/CS1600E
accessories not recommended by the manufacturer of
this product. The use of attachments or accessories not
recommended can result in serious personal injury.
cause serious personal injury, always remove the battery
pack from the tool when assembling parts, making
adjustments, cleaning, or when not in use.
L-2 Tension Adjusting Pin
L-3 Guide Bar Slot
Before each use, inspect the entire product for damaged,
L-4 Sprocket
missing, or loose parts, such as screws, nuts, bolts, caps, etc.
Securely tighten all fasteners and caps and do not operate
this product until all missing or damaged parts are replaced.
APPLICATION
You may use this product for basic felling, limbing, pruning
and woodcutting of lumber and trees.
NOTICE:
purpose. Any other use is deemed to be a case of misuse.
FILLING BAR AND CHAIN LUBRICANT
near the oil or the chain saw. Oil may spill and cause a fire.
NOTICE:
purchase. It is essential to fill the tank with oil before use.
The chain is automatically lubricated with chain oil during
operation.
1. Position the chain saw on its side with its oil tank cap
2. Clean the cap as well as the area around and then turn it
3. Carefully pour the specifically designed oil into the
4. Wipe off any excessive oil and replace the cap.
NOTICE:
window. When the oil is no longer visible in the inspection
window, stop use immediately and refill.
ATTACHING/DETACHING THE BATTERY PACK
Fully charge before first use.
To Attach (Fig. O)
Align the battery ribs with the mounting slots and press
the battery pack down until you hear a "click".
To Detach (Fig. P)
Depress the battery-release button and pull the battery
pack out.
WARNING: Do not use any attachments or
WARNING:
To prevent accidental starting that could
The tool is to be used only for its prescribed
WARNING:
Do not smoke or bring any fire or flame
The chain saw is not filled with oil at the time of
facing towards.
counterclockwise to remove (Fig. N).
tank until reaching the bottom of the filter neck.
With upright position, oil should fill the inspection