Description Of Symbols; General Safety Warnings - Silverline 633629 Manual Del Usario

GB

Description of Symbols

The rating plate on your tool may show symbols. These represent important
information about the product or instructions on its use.
Wear hearing protection
Wear eye protection.
Wear breathing protection
Wear head protection
Wear hand protection
Read instruction manual
DO NOT use with compressed gas cylinders!
Toxic fumes or gases!
Conforms to relevant legislation and safety standards
Environmental Protection
Air tools should not be disposed of with household waste. They
contain traces of oil and other lubricants. Please recycle where
facilities exist. Check with your local authority or retailer for
recycling advice.
Specification
Operating pressure: ....................................... 3-6bar (43-87psi)
Maximum operating pressure: ....................... 8bar (116psi)
Air consumption: ............................................ 156L/min (5.5cfm)
Air fluid nozzle diameter: ............................... 6mm
Material nozzle diameter: ............................... 3mm
Type of feed: .................................................. Suction
Material feed hose: ........................................ 10.5 x 18mm x
Recommended abrasives:.............................. aluminium oxide,
sand, glass beads, silicon carbide, walnut shells
Air inlet: ......................................................... ¼" BSP, supplied
with two male airline quick connectors (EN-6 'UK' and
EQ-4 'European' types)
Minimum air supply hose diameter: ............... 9.5mm (3/8")
Weight ........................................................... 0.45kg
Noise and vibration information:
Level of sound pressure according to EN 1953/A1:2009:
Sound pressure ............................................ L
Sound power ................................................ L
Uncertainty ................................................... K = 3dB
The sound intensity level for the operator may exceed 85dB(A) and
sound protection measures are necessary.
Vibration emission value ............................... a
As part of our ongoing product development, specifications of
Silverline products may alter without notice.
4
1.5m, rubber hose
= 90dB(A)
PA
= 101dB(A)
WA
= 2.5m/s
2
h
Noise and Vibration
Sound and vibration levels in the specification are determined according to
ISO 28927-3. The figures given can be used to compare similar tools tested
to this standard. These figures may be used to assess exposure to noise
and vibration levels.
The figures represent normal use for the tool in normal working condition.
A poorly maintained, incorrectly assembled or misused tool may produce
increased levels of noise and vibration. The total working period that
you can operate this tool must factor in periods where the tool is idle or
switched off. Allow frequent rest breaks when operating this tool.
It is in the interest of users to maximise their safety using the correct safety
equipment, like ear defenders that protect against loud or repetitive noise,
and anti-vibration gloves that minimise vibration. Do not operate the tool
with your hands below a normal comfortable temperature, as vibration will
have a greater effect.
Sound
The noise directive was introduced to protect against the risk to health and
safety arising or likely to arise from exposure to noise and risk of hearing.
The Directive can be used to define noise exposure and the physical
parameters, such as peak sound pressure and daily and weekly exposure
level. Particular attention should be taken to exposure level and duration.
For more information on the Noise Directives 2003/10/EC and 2000/14/EC,
please visit The European Agency for Safety and Health at work
- www.osha.europa.eu.
Vibration
The European Physical Agents (Vibration) Directive 2002/44/EC was
introduced to control the exposure of vibration at work. The Directive
enables users of tools to make informed decisions on the amount of time
spent working. Those who regularly operate high vibration equipment
over a sustained period of time are at a higher risk of health problems.
ISO 28927-3 measures vibration in three directions which is known as
tri-axial or vector sum measurement. When operating high vibration
equipment, ensure not to exceed exposure levels. For more details on The
Vibration Directive 2002/44/EC please visit The European Agency for Safety
and Health at work -www.osha.europa.eu.

General Safety Warnings

• For multiple hazards, read and understand the safety instructions before
installing, operating, repairing, maintaining, changing accessories on,
or working near this tool. Failure to do so can result in serious
bodily injury
• Only qualified and trained operators should install, adjust, or use this tool
• Do not modify this tool. Modifications can reduce the effectiveness of
safety measures and increase the risks to the operator
• Do not discard the safety instructions; give them to the operator
• Do not use this tool if it has been damaged
• Tools shall be inspected periodically to verify that the ratings and
markings required by this part of ISO 11148 are legibly marked on
the tool. The employer/user should contact the manufacturer to obtain
replacement marking labels when necessary
WARNING: This appliance is not intended for use by persons
(including children) with reduced, physical or mental capabilities or lack
of experience or knowledge unless they have been given supervision or
instruction concerning use of the appliance by a person responsible for their
safety. Children must be supervised to ensure that they do not play with
the appliance.
Projectile Hazards
• Be aware that failure of the workpiece or accessories, or even of the
inserted tool itself, can generate high-velocity projectiles
• Always wear impact-resistant eye protection during operation of this tool.
The grade of protection required should be assessed for each use
• For overhead work, wear a safety helmet
• The risks to others should also be assessed at this time
• Ensure that the workpiece is securely fixed