Technical Specification; Heat Settings - WAGNER HT2000 Manual De Instrucciones

!
PLEASE READ BEFORE USE
DO NOT touch the nozzle.
●
DO NOT change/rotate the nozzle while
●
the unit is turned on.
DO NOT leave the heat gun unattended
●
when it is switched on.
DO NOT allow children to operate or play
●
with the heat gun.
DO NOT carry the heat gun by the mains
●
cable.
DO NOT allow heat to be directed onto
●
the mains cable.
DO NOT use the heat gun as a hair dryer.
●
DO NOT restrict air flow from the nozzle
●
outlet or fan inlets.
DO NOT allow the heat gun to become
●
damp or be operated in damp conditions.
DO NOT use the heat gun close to
●
inflammable materials because heat may
be conducted to combustible materials
which are out of sight.
DO NOT apply to the same place for a
●
long time.
DO NOT under any circumstances aim
●
the heat gun at another person or animal.
DO NOT use when explosive vapour or
●
dust is in the air.
Danger of burns - Always wear a pair of
heavy grade, non PVC type work gloves.
Danger of fire or explosion if the
appliance is not used with care.
When changing the nozzle, switch off and
●
allow the accessory and nozzle to cool.
Re-Set thermal cut out – This heat gun is fitted with a resettable cut-out. If you find the fan
is on but the heating element is off, hold the gun away from the work piece and allow the fan
to cool the element. It should reset in approx. 1min.

TECHNICAL SPECIFICATION

Power Supply
Max. Output
Temp at Outlet
Weight
(excl. nozzles)
*MAX. temperatures achieved with
concentrator nozzle.
ABOUT THE HT2000
The HT2000 is a highly versatile electric heat
gun which can be used for many different
applications, such as:
Removal of paint
●
Defrosting metal water pipes
●
Forming and welding plastic
●
Reducing heat shrinking tubing
●
Soldering
●
SAFETY OPERATING INSTRUCTIONS
230V 50Hz~
2000 Watts
Position 1) 350°C*
Position 2) 600°C*
750g
After use stand the heat gun up vertically
●
(on its rear end) and allow to completely
cool down.
A hot nozzle can cause damage.
●
Before every use check the condition of
●
the plug and cable. If these are damaged in
any way do not use. Repairs must be
carried out by a fully qualified electrician.
Always ensure there is adequate
●
ventilation as gases and vapours may be
given off when stripping paint. Ensure that
protective goggles and masks are used.
Poisonous or inflammable gases may be
●
produced when working with paints
(especially older type lead paints),
varnishes, plastics and similar materials.
Ensure the heat gun switch is in the off
●
position when connecting to the mains.
Ensure children and pets are kept away
●
from the work area.
It is recommended a RCD (residual
●
current device) rated at 30mA trip current
is fitted into the mains socket-outlet for
added protection against electric shock.
This product is intended for 'household'
●
use only.
This appliance is not intended for use by
●
persons (including children) with reduced
physical, sensory or mental capabilities,
or lack of experience and knowledge,
unless they have been given supervision or
instruction concerning use of the appliance
by a person responsible for their safety.
TO OBTAIN THE BEST RESULTS FROM
YOUR HEAT GUN PLEASE READ THE
INSTRUCTIONS CAREFULLY BEFORE
USE.

HEAT SETTINGS

The Heat Gun has two settings:
1. Low heat (Switch Down) - for use
where the work surface or
surroundings must not be allowed
to get too hot.
Setting~350°C.
2. High heat (Switch Up) - for faster
heat up time of the work surface
where you can also operate the
gun at a greater distance.
Setting~600°C.
3
RU
PL
TR
DK
NL
S