If not used properly this product can be dangerous! This product can cause serious injury
to the operator and others, the warnings and safety instructions must be followed to
ensure reasonable safety and efficiency in using this product. The operator is responsible
for following the warning and safety instructions in this manual and on the product.
Explanation of Symbols on the product
Warning
Read the user instructions carefully
to make sure you understand all the
controls and what they do
Always keep the product on the ground
when operating. Tilting or lifting the
product may cause stones to be thrown
out
Keep bystanders away. Do not
operater whilst people especially
children or pets are in the area
Switch off! Remove plug from mains
before adjusting, cleaning or if cable
is entangled or damaged. Keep the
cable away from the blade.
Beware of severing toes or hands.
Do not put hands or feet near a
rotating blade.
Blade continues to rotate after the
machine is switched off. Wait until all
machine components have completely
STOP
stopped before touching them.
Do not use in the rain or leave the
product outdoors while raining
Keep the cable supply away from
the cutting means
General
1. Never allow children or people unfamiliar with
these instructions to use the product. Local
regulations may restrict the age of the
operator.
2. Only use the product in the manner and for
the functions described in these instructions.
3. Never operate the product when you are
tired, ill or under the influence of alcohol,
drugs or medicine.
4. The operator or user is responsible for
accidents or hazards occurring to other
people or their property.
Electrical
1. The use of a Residual Current Device (R.C.D.)
with a tripping current of not more than 30mA is
recommended. Even with a R.C.D. installed
100% safety cannot be guaranteed and safe
working practice must be followed at all times.
Check your R.C.D. every time you use it.
2. Before use, examine cable for damage,
ENGLISH - 1
Safety
replace it if there are signs of damage or
ageing.
3. Do not use the product if the electric cables
are damaged or worn
4. Immediately disconnect from the mains
electricity supply if the cable is cut, or the
insulation is damaged. Do not touch the electric
cable until the electrical supply has been
disconnected. Do not repair a cut or damaged
cable. Replace it with a new one.
5. Your extension cable must be uncoiled, coiled
cables can overheat and reduce the efficiency
of your mower.
6. Keep cable away from product, always work
away from the power point mowing up and
down, never in circles.
7. Do not pull cable around sharp objects.
8. Always switch off at the mains before
disconnecting any plug, cable connector or
extension cable.
9. Switch off, remove plug from mains and
examine electric supply cable for damage or
ageing before winding cable for storage. Do
not repair a damaged cable, replace it with a
new one. Use only Flymo replacement cable.
10.Always wind cable carefully, avoiding kinking.
11. Never carry the product by the cable.
12.Never pull on the cable to disconnect any of the
plugs.
13.Use only on AC mains supply voltage shown
on the product rating label.
14.Husqvarna products are double insulated to
EN60335. Under no circumstances should
an earth be connected to any part of the
product.
Cables
Use only 1.00mm
length maximum.
Maximum rating:
1.00mm
2
size cable 10 amps 250 volts AC
1. Mains cables and extensions are available
from your local Approved Service Centre.
2. Only use extension cables specifically
designed for outdoor use.
Preparation
1. While using your product always wear
substantial footwear and long trousers.
2. Make sure the lawn is clear of sticks, stones,
bones, wire and debris; they could be thrown
by the blade.
3. Before using the machine and after any
impact, check for signs of wear or damage
and repair as necessary.
4. Replace worn or damaged blades together
with their fixings in sets to preserve balance.
Use
1. Use the product only in daylight or good
artificial light.
size cable up to 40 metres
2