Descargar Imprimir esta página

Stanley QDC100 Serie Instrucciones De Instalación página 4

Publicidad

Idiomas disponibles

Idiomas disponibles

OPTION
DOOR CLOSER MOUNTED ON DOOR ON PUSH SIDE OF DOOR
DOOR OPENING: 180°
This diagram shows LEFT-HAND DOOR. For RIGHT-HAND DOOR, rotate door closer 180º.
Hinge or Pivot
PROCEDURE:
1. Before installing, turn back
check selector valve clockwise
all the way in (valve can be
found on opposite side of closer
from back check screw side).
2. Adjust spring power to match door width as indicated in chart on page 1.
3. Mount closer on door using dimensions shown. Tube end faces towards latch.
If pivots are used, locate closer and parallel bracket from centerline of pivot.
4. Place open-end wrench on bottom shaft and turn toward hinge jamb about 30˚. Place main
arm on top shaft. Insert arm screw into top of shaft and tighten.
5. Attach parallel bracket on frame using dimensions shown. Use spacer block, as shown, for
extra bracket support.
6. Attach rod and shoe to parallel bracket, as shown.
7. Insert rod in forearm. Insert main arm to closer parallel to door. Insert forearm set screw and
tighten. If hold-open arm is used, nut is on top for RH door and bottom for LH door.
ADJUSTMENTS:
SWEEP / LATCH
"Normal" closing time from 90˚ open position to door stop position is 4-6 seconds evenly divided
between main swing speed and latch swing speed. Use hex wrench (furnished) to adjust speed.
To slow main speed of door, turn sweep speed control screw clockwise; to slow latch speed, turn
latch speed control screw clockwise.
BACK CHECK
To increase back check force, turn back check screw clockwise. DO NOT USE ABRUPT BACK
CHECK MOVEMENT OR EXPECT DOOR CLOSER TO ACT AS A DOOR STOP.
DELAYED ACTION
To increase delayed action closing time, turn delayed action control screw clockwise.
HOLD-OPEN ADJUSTMENT
(when hold-open arm is used)
Loosen adjusting nut, open door to desired hold open position and tighten nut. DO NOT PERMIT
DOOR TO SWING BEYOND HOLD-OPEN SETTING.
COVER
Remove appropriate perforated cover tab then push cover against door. Tighten both cover screws securely.
C
: PARALLEL MOUNT
1 11/16"
(43mm)
1 1/16"
(27mm)
5 HOLES FOR #14
ALL-PURPOSE OR
1/4-20 (M6x1.0)
MACHINE SCREWS
11 1/2" (292mm) = 90° OPENING
10" (254mm) = 120° OPENING
7 7/8" (200mm) = 180° OPENING
2 5/16"
(58.7mm)
2 1/4"
(57mm)
9 1/2" (241mm) = 90° OPENING
8" (203mm) = 120° OPENING
6 1/2" (165mm) = 180° OPENING
1 11/16"
(43mm)
1 1/16"
(27mm)
1 3/4"
5/16"
(44.5mm)
(8mm)
11/16"
(17.5mm)
2 HOLES FOR #14
ALL-PURPOSE OR 1/4-20
(M6x1.0) MACHINE SCREWS
1"
3"
(25.4mm)
(76.2mm)
1"
(25.4mm)
BACK CHECK
SCREW
DELAYED ACTION
SCREW
SWEEP SPEED
SCREW
LATCH SPEED
SCREW
5
SPACER
BLOCK
PARALLEL
BRACKET
OR
ARM
SCREW
4"
(101.6mm)
4 HOLES FOR #14
ALL-PURPOSE OR
1/4-20 (M6x1.0)
MACHINE SCREWS
2
SPRING POWER
ADJUSTING
SCREW
ARM SCREW
3
4
30°
6
SHOE
7
ROD
FOREARM
SET SCREW
PERFORATED
COVER TABS
1
BACK CHECK
SELECTOR
SCREW
MAIN
ARM
COVER

Publicidad

loading

Este manual también es adecuado para:

Qdc111