Cooper Lighting HALO TGS3S401FSRB Instrucciones

PACKAGING CONTENTS
B. Mounting bracket
A. Light fixture
TGS3S401FSRB
TGS3S401FSRW
TGS2S402FRRB
TGS2S402FRRW
TGS2S402FSRB
TGS2S402FSRW
TGS3S403FRRB
TGS3S403FRRW
D. (2) #6-32 x 3/4 in. and (2) #8-32 x 3/4 in. junction box screws
TGS3S301FSRB
(use the size that fits your junction box)
D. (2) #6-32 x 3/4 in. and (2) #8-32 x 3/4 in. junction box screws
(use the size that fits your junction box)
TGS3S301FSRW
TGS2S302FRRB
unction box screws
TGS2S302FRRW
TGS2S302FSRB
TGS2S302FSRW
TGS3S303FRRB
TGS3S303FRRW
ENGLISH
ITEMS REQUIRED
(Purchase separately)
• Phillips screwdriver
• Outdoor weatherproof silicone caulking
IMPORTANT SAFETY INSTRUCTIONS
When using product, basic precautions should always be followed, including the following:
• Heed all warnings, including below warnings AND those included on product.
• Save these instructions and warnings.
• For outdoor use only.
• cULus LISTED for wet location.
• Disassembling your fixture will void the warranty.
• Your fixture is prewired and preassembled for easy installation.
WARNING
• Read and follow these instructions.
• Risk of fire/electric shock. If not qualified, consult an electrician.
• Disconnect power at fuse or circuit breaker before installing or servicing.
CAUTION
• Connect fixture to a 120 volt, 60 Hz power source. Any other connection voids
the warranty.
• Fixture should be installed by persons with experience in household wiring or by
a qualified electrician. The electrical system, and the method of electrically con-
necting the fixture to it, must be in accordance with the National Electrical Code
and local building codes.
• Fixture designed for wall or eave mount to a junction box only. Mount fixture
to a grounded, recessed-mounted standard junction box marked for use in wet
locations.
• Fixture can be mounted to an outdoor rated surface mount junction box when
used with the adapter plate kit (sold separately TGS-KIT-MTG). See kit instruc-
tions for proper installation methods.
• Suitable for wall mount or eave mount only. NOT suitable for ground mount installation.
FCC DECLARATION OF CONFORMITY
This device complies with part 15 of the FCC Rules. Operation is subject to the following 2
conditions: (1) This device may not cause harmful interference, and (2) this device must accept
any interference received, including interference that may cause undesired operation.
NOTE: This equipment has been tested and found to comply with the limits for a Class B
digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide
reasonable protection against harmful interference in a residential installation. This
equipment generates uses and can radiate radio frequency energy and, if not installed
Questions?/ Des questions? / ¿Preguntas? 1-800-334-6871 ConsumerProducts@cooperlighting.com
PACKAGING CONTENTS / CONTENU DE L'EMBALLAGE/ CONTENIDO DEL PAQUETE
A. Light fixture
PACKAGING CONTENTS
PACKAGING CONTENTS
Appareil d'éclairage
Accesorio
A. Light fixture
A. Light fixture B. Mounting bracket
A. Light fixture
B. Mounting bracket
E. Adapter Plate Kit (Sold Separately)
D. (2) #6-32 x 3/4 in. and (2) #8-32 x 3/4 in. junction box screws
Trousse de plaque d'adaptation
(use the size that fits your junction box)
D. (2) #6-32 x 3/4 in. and (2) #8-32 x 3/4 in. junction box screws
E. Adapter Plate Kit
(use the size that fits your junction box)
(vendue séparément)
Kit de placa adaptadora
E. Adapter Plate Kit
(se vende por separado)
#TGS-KIT-MTG
Instruction Manual / Manuel d'instructions/ Instrucciones
C. Gasket
PACKAGING CONTENTS
B. Mounting bracket C. Gasket
PACKAGING CONTENTS
Joint d'étanchéité
Support de montage
Junta
Soporte de montaje
B. Mounting bracket
C. Gasket
B. Mounting bracket
C. Gasket
F. Decorative screw cover cap
E. Adapter Plate Kit
F. Decorative screw cover caps
E. Adapter Plate Kit Cache-vis décoratif
F. Decorative screw cover caps
E. Adapter Plate Kit
Cubierta tapatornillos decorativa
F. Decorative screw cover caps
and used in accordance with the instructions, may cause harmful interference to radio
communications. However, there is no guarantee that interference will not occur in a
particular installation. If this equipment does cause harmful interference to radio or tele-
vision reception, which can be determined by turning the equipment off an on, the user is
encouraged to try to correct the interference by one or more of the following measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from
that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.
WARNING: FCC Regulations state that any unauthorized changes or
modifications to this equipment not expressly approved by the manufacturer
could void the user's authorization to operate this equipment.
SAVE THESE INSTRUCTIONS.
FOR BEST RESULTS
• Install light 8-16 feet above the ground.
• When installing two fixtures on one switch, make sure the switch is rated for at
least a 1 A inductive load.
ADJUSTING THE LUMEN OUTPUT
• This product features selectable lumen output.
Choose between three preset lumen outputs
on the dial of the base housing before, during,
or after installation (fig. 1)
• These settings are designated by the
abbreviations located on the center dial on the
base housing (fig. 1):
- High = 3000lm (Triple Head and Single Head) or 2500lm (Twin Head Fixtures)
- Med = 2500lm (Triple Head), 2200lm (Single Head), or 2000lm (Twin Head)
- Low = 2000lm (Triple Head), 1500lm (Single Head and Twin Head)
• Use a flathead head screwdriver to rotate the dial so the arrow points toward the
desired setting.
• DO NOT USE a power tool or over-rotate the dial.
MOUNTING AND WIRING YOUR FIXTURE
WARNING: Risk of electric shock. Disconnect
power at fuse or circuit breaker before installing
or servicing.
NOTE: Fixture can be wall or eave mounted (Fig. 2).
NOTE: Mounting bracket mounts to recessed mounted
standard junction boxes (Fig. 3). Junction box must be
at least 1-1/2 inch in depth for proper installation for
recessed mount application. For surface mount junction box
installation, refer to installation instructions included with
the adapter plate kit (E).
1
D. (2) #6-32 x 3/4 in. and (2) #8-32 x 3/4 in. junction
box screws
2 vis nº 6 de 32 x 3/4 po et 2 vis nº 8 de 32 x 3/4
C. Gasket
po pour boîtier de jonction
C. Gasket
(2) cajas de empalmes de 6-32 x 3/4 pulgadas y de
8-32 x 3/4 pulgadas tornillos
G. Wire connector
F. Decorative screw cover caps
Serre-fil
F. Decorative screw cover caps
Conectores de cable
FLOOD
1
FIG.1
2
Wall mount
Wall mount
Wall Mount Eave Mount
Eave mount
FIG.2
Eave mount
FIG.2